- Area
- Gloucestershire
- Postcode district
- BS15
- Nation
- England
- Guide price
- From £9,600 inc VAT
- Survey
- Free for installation enquiries
What to know about air source heat pump installation in Kingswood
The question for a Kingswood home is rarely whether a heat pump can work, but what needs to change to make it work well: radiator sizes, pipework, controls and where the unit goes.
In Kingswood, cylinder space is planned with you, often in an airing cupboard, utility room or garage. Installers working in Kingswood plan the order of work so heating and hot water are off for as short a time as practical.
We survey your home, design a heat pump system around its real heat loss, and manage the installation from the first visit to the MCS certificate.
- Owners who want one contract covering design, fitting and paperwork
- Households with room for a hot water cylinder
- Homes replacing a gas, oil, LPG or electric heating system
What's included
- Outdoor unit, hot water cylinder and weather compensation controls
- Removal of the old boiler or heaters
- Radiator and pipework changes where the design needs them
- System design, unit sizing and a written quote
- Commissioning, handover and a walk-through of the controls
Terraced streets in Kingswood often mean a compact unit position at the rear, so siting and sound levels are checked carefully.
Grants and rules for heat pumps in England
In England the Boiler Upgrade Scheme gives £7,500 towards an air source heat pump (£9,000 if it replaces oil or LPG, from 21 July 2026 to 31 March 2027), and since 28 April 2026 a valid EPC is no longer needed. The grant is applied for by the MCS-certified installer and shown as a deduction on your Kingswood quote.
There is no VAT on installing a heat pump anywhere in the UK until 31 March 2027. In England most houses can have an air source heat pump under permitted development, provided the unit meets the MCS noise and siting standards; the old 1 m boundary limit was removed on 29 May 2025. We flag listed buildings, flats and sensitive conservation-area positions at survey.
Air source heat pump installation prices in Kingswood
Here are typical prices for air source heat pump installation in Gloucestershire, installed and including VAT. Use the guide price tool for a figure based on your home, then a survey confirms it in writing.
| Home | Typical size | Installed guide price | After £7,500 grant |
|---|---|---|---|
| 1–2 bedroom flat or small terrace | 4–5 kW | £9,600–£12,650 | £2,100–£5,150 |
| 2–3 bedroom terrace or semi | 5–7 kW | £10,600–£13,650 | £3,100–£6,150 |
| 3 bedroom semi or small detached | 6–9 kW | £12,100–£15,650 | £4,600–£8,150 |
| 4 bedroom detached | 8–12 kW | £14,150–£18,200 | £6,650–£10,700 |
| 5+ bedroom or larger older house | 11–16 kW | £16,650–£22,750 | £9,150–£15,250 |
Installed, inc VAT: unit, cylinder, controls, minor pipework and commissioning.
Winter daylight and heating in Kingswood
On the shortest day Kingswood gets about 7 hours 50 minutes of daylight, and the winter sun reaches only around 15° above the horizon at noon. Winters this far south are milder than in most of the UK, which helps a heat pump run at low flow temperatures for much of the season.
How installation works in Kingswood
- Send your postcode and a few details, or use the guide price tool.
- A surveyor visits your Kingswood home, measures every room and checks where the outdoor unit can go.
- You receive a heat loss design and a fixed written quote, with any grant shown where it applies.
- Installers fit the unit, cylinder and any radiator changes, typically over 2–4 days on site.
- The system is commissioned, set up with weather compensation and handed over with the paperwork.
Air source heat pump installation in Kingswood: questions
What size heat pump does a Kingswood home need?
It depends on the heat loss, not the postcode. As a rough guide, a 3 bedroom semi often needs 6–9 kW, but the room-by-room survey sets the actual size for your Kingswood home.
How long does a heat pump survey take in Kingswood?
A home survey in Kingswood usually takes one to two hours. The surveyor measures every heated room, checks windows, walls and radiators, and looks at where the outdoor unit and cylinder can go.
Where would the outdoor unit go on a Kingswood house?
Usually at the side or rear, on a level base with space around it for airflow and servicing, away from bedroom windows where possible. The surveyor checks positions at your Kingswood home.
Can I cancel after accepting the quote?
Nothing is ordered until you accept the written quote. Where the contract is agreed away from our premises, for example at your kitchen table, you can cancel within 14 days under the Consumer Contracts Regulations 2013. If you ask us to start sooner and then cancel, you pay only for work done up to that point.
How long does an air source heat pump installation take?
A typical home installation takes 2–4 days on site. It takes longer if several radiators are being replaced, pipework is being upgraded or the cylinder is going in a new location. Your quote sets out the expected programme, including when you will be without heating and hot water. Timings are typical rather than fixed, because older homes sometimes reveal surprises once floorboards are lifted.