- Area
- Kent
- Postcode district
- CT9
- Nation
- England
- Guide price
- Priced after survey
- Survey
- Free for installation enquiries
Heat loss survey in Margate: what to expect
Homes around Margate range from older terraces to newer estates, and each needs a different design. That is why we survey before we quote.
A surveyor visits your Margate home to measure each room, window and wall before any heat pump is sized. For Margate homes with extensions or loft conversions, each part of the house is assessed on its own construction.
Every heat pump we quote starts with a room-by-room heat loss survey, free with installation enquiries and also available as a stand-alone report.
- Anyone getting a heat pump quote, as the first step
- Landlords comparing properties before deciding where to switch first
- Homes with an existing heat pump that seems undersized or expensive to run
What's included
- Radiator schedule with any upgrades needed for each room
- Electrical supply and network operator notes
- Outdoor unit siting options and noise check
- Room-by-room heat loss calculation using the MCS method
- Written results in your quote, or a stand-alone report if you order one
The survey in Margate includes a check of where the outdoor unit could sit and how its sound would reach neighbours.
Grants and rules for heat pumps in England
In England the Boiler Upgrade Scheme gives £7,500 towards an air source heat pump (£9,000 if it replaces oil or LPG, from 21 July 2026 to 31 March 2027), and since 28 April 2026 a valid EPC is no longer needed. The grant is applied for by the MCS-certified installer and shown as a deduction on your Margate quote.
There is no VAT on installing a heat pump anywhere in the UK until 31 March 2027. In England most houses can have an air source heat pump under permitted development, provided the unit meets the MCS noise and siting standards; the old 1 m boundary limit was removed on 29 May 2025. We flag listed buildings, flats and sensitive conservation-area positions at survey.
Heat loss survey costs around Margate
The ranges below are typical installed prices for homes in Kent, including VAT. A survey sets the exact figure, because two similar-looking houses in Margate can need quite different radiators and pipework.
| Survey | Guide price |
|---|---|
| Home survey and heat loss calculation with an installation quote | Free |
| Stand-alone heat loss survey and report | £150–£410 |
Inc VAT. A stand-alone report is for homeowners who want the design without an installation quote.
Designing for Margate's winters
Margate sees roughly 7 hours 51 minutes of daylight in late December against 16 hours 37 minutes in June. Milder southern winters suit heat pumps well, though the system is still sized for a cold snap rather than an average day.
How installation works in Margate
- Start online with a guide price or call us.
- A home survey in Margate gives us the room-by-room heat loss.
- Your written quote sets out the design, the price and the grant position where you live.
- Installation is booked for dates that suit you; most homes take 2–4 days on site.
- After commissioning you get a handover of the controls and settings, plus the certificates.
Heat loss surveys in Margate: questions
Do you cover Broadstairs as well as Margate?
Yes. We arrange surveys and installation in Broadstairs, which is about 2 miles south-east of Margate, and across Kent.
What size heat pump does a Margate home need?
It depends on the heat loss, not the postcode. As a rough guide, a 3 bedroom semi often needs 6–9 kW, but the room-by-room survey sets the actual size for your Margate home.
Where would the outdoor unit go on a Margate house?
Usually at the side or rear, on a level base with space around it for airflow and servicing, away from bedroom windows where possible. The surveyor checks positions at your Margate home.
What is a design flow temperature?
The design flow temperature is the temperature of the water sent to your radiators or underfloor heating on the coldest design day. Heat pumps are more efficient at lower flow temperatures, typically around 35–50°C. Choosing it is a balance: a lower figure improves efficiency but can mean larger radiators in some rooms, so the design shows both.
Why can't you size the heat pump from my boiler?
Boilers are often much larger than a home's real heat loss, because they are sized for fast hot water and quick warm-ups. Matching a heat pump to the boiler's output usually means an oversized unit that costs more and switches on and off too often. A room-by-room calculation finds the actual heat demand, which is what the heat pump needs to meet.