- Area
- Angus and Dundee
- Postcode district
- DD8
- Nation
- Scotland
- Guide price
- From £90 inc VAT
- Visit
- Rate agreed in advance
What to know about heat pump repairs in Kirriemuir
Aftercare matters as much as installation. For a heat pump in Kirriemuir the visit checks the outdoor unit, the water circuit and the controls, and the engineer explains any settings that would help the system run more efficiently.
For repeated faults in Kirriemuir, the engineer looks at the system design as well as the failed part. Across Kirriemuir and Angus and Dundee, refrigerant repairs on split systems are carried out by an F-gas certified engineer.
When a heat pump shows an error, loses pressure or stops heating, an engineer diagnoses the cause and explains the repair and its cost before fixing it.
- Rooms or hot water not getting warm enough
- Heat pumps installed by another company that need a second opinion
- Heat pumps showing an error code or fault light
What's included
- Fault-finding visit at a rate agreed before attending
- System refill, venting and recommissioning after the repair
- Reading of error history and operating data
- Testing of sensors, pumps, valves, pressures and electrics
- A clear explanation of the fault and a price for the repair before work goes ahead
Repairs in Kirriemuir that need a part ordered are explained and priced before the engineer leaves.
Grants and rules for heat pumps in Scotland
In Scotland, heat pump funding comes through Home Energy Scotland rather than the Boiler Upgrade Scheme: a grant of up to £7,500 (up to £1,500 extra for eligible rural and island homes) and an optional interest-free loan of up to £7,500. For a Kirriemuir home, apply and receive the written offer before the installation date is fixed.
What to budget for heat pump repairs in Kirriemuir
Guide prices for Angus and Dundee, including VAT. We agree the visit rate before anyone attends, so there are no surprises on the day.
| Repair | Guide price |
|---|---|
| Fault-finding visit and diagnosis | £90–£180 |
| Sensor or thermistor replacement | £120–£280 |
| Expansion vessel or pressure relief valve | £150–£350 |
| Circulating pump replacement | £250–£480 |
| Fan motor replacement | £300–£650 |
| Refrigerant leak repair and re-gas (split systems) | £350–£950 |
| Main control board (PCB) replacement | £450–£1,100 |
Inc VAT. The fault-finding rate is agreed before we attend; repairs are priced in writing before parts are ordered.
Designing for Kirriemuir's winters
Kirriemuir has about 6 hours 47 minutes of daylight at midwinter against 17 hours 48 minutes in midsummer. Heat pumps are designed to keep working well below freezing, but the design temperature for the survey is set for local conditions, not an average day.
How a visit works in Kirriemuir
- Tell us the make if you know it, the error code or symptoms, and send photos of the unit and controller.
- We confirm the fault-finding rate and arrange a visit in Kirriemuir.
- The engineer diagnoses the fault and gives you a written price for the repair.
- Parts are ordered once you agree, and the repair is completed and tested.
Heat pump repairs in Kirriemuir: questions
Do you also cover Forfar?
Yes. We arrange heat pump servicing and repairs in Forfar, which is about 5 miles south-east of Kirriemuir, and across Angus and Dundee.
Will the engineer need access indoors as well as outside?
Usually yes. The outdoor unit, the hot water cylinder, the controls and the pipework and valves indoors are all part of the visit, so allow access to each.
How much does a visit cost in Kirriemuir?
The rate for a service or fault-finding visit is agreed before anyone attends. Any repair is priced in writing before parts are ordered, so you decide before work goes ahead.
Can you repair a heat pump installed by another company?
Yes. We carry out fault-finding and repairs on heat pumps installed by other companies, including monobloc and split systems. Tell us the make, model and approximate age when you get in touch, plus any error code shown. If the system is still under the manufacturer's warranty, it may be quicker to contact the original installer or manufacturer first.
Do refrigerant repairs need a specialist?
Yes. Any work on a heat pump's refrigerant circuit, such as tracing a leak, replacing a component or re-gassing, must by law be done by an F-gas certified engineer where the refrigerant is fluorinated, such as R32; units using R290 (propane) need an engineer trained in flammable refrigerants. On split systems the refrigerant runs through pipes inside your home, so leaks there are more likely than on sealed monobloc units.