- Area
- Argyll and Bute
- Postcode district
- PA31
- Nation
- Scotland
- Guide price
- From £100 inc VAT
- Visit
- Rate agreed in advance
Heat pump repairs in Lochgilphead: what to expect
Whoever installed your heat pump, aftercare can be arranged in Lochgilphead. Tell us the make and model and roughly how old it is, and we will set out what the visit involves before you book.
We repair heat pumps in Lochgilphead whoever installed them, including older monobloc and split systems. Outdoor units in exposed spots around Lochgilphead can ice more heavily, so siting is checked as part of any icing fault.
When a heat pump shows an error, loses pressure or stops heating, an engineer diagnoses the cause and explains the repair and its cost before fixing it.
- Outdoor units that have become noisy, iced up or keep switching on and off
- Rooms or hot water not getting warm enough
- Systems losing pressure or needing frequent topping up
What's included
- Testing of sensors, pumps, valves, pressures and electrics
- Reading of error history and operating data
- System refill, venting and recommissioning after the repair
- Fault-finding visit at a rate agreed before attending
- Refrigerant repairs by an F-gas certified engineer where needed
Across Lochgilphead and Argyll and Bute, refrigerant repairs on split systems are carried out by an F-gas certified engineer.
Grants and rules for heat pumps in Scotland
In Scotland, heat pump funding comes through Home Energy Scotland rather than the Boiler Upgrade Scheme: a grant of up to £7,500 (up to £1,500 extra for eligible rural and island homes) and an optional interest-free loan of up to £7,500. For a Lochgilphead home, apply and receive the written offer before the installation date is fixed.
What to budget for heat pump repairs in Lochgilphead
Guide prices for Argyll and Bute, including VAT. We agree the visit rate before anyone attends, so there are no surprises on the day.
| Repair | Guide price |
|---|---|
| Fault-finding visit and diagnosis | £100–£190 |
| Sensor or thermistor replacement | £130–£300 |
| Expansion vessel or pressure relief valve | £160–£380 |
| Circulating pump replacement | £270–£520 |
| Fan motor replacement | £320–£700 |
| Refrigerant leak repair and re-gas (split systems) | £380–£1,050 |
| Main control board (PCB) replacement | £490–£1,200 |
Inc VAT. The fault-finding rate is agreed before we attend; repairs are priced in writing before parts are ordered.
Winter daylight and heating in Lochgilphead
Lochgilphead has about 6 hours 56 minutes of daylight at midwinter against 17 hours 38 minutes in midsummer. Heat pumps are designed to keep working well below freezing, but the design temperature for the survey is set for local conditions, not an average day.
How a visit works in Lochgilphead
- Tell us the make if you know it, the error code or symptoms, and send photos of the unit and controller.
- We confirm the fault-finding rate and arrange a visit in Lochgilphead.
- The engineer diagnoses the fault and gives you a written price for the repair.
- Parts are ordered once you agree, and the repair is completed and tested.
Lochgilphead is in an area we cover by arrangement, so survey dates and any travel costs are confirmed individually in your quote.
Heat pump repairs in Lochgilphead: questions
How much does a visit cost in Lochgilphead?
The rate for a service or fault-finding visit is agreed before anyone attends. Any repair is priced in writing before parts are ordered, so you decide before work goes ahead.
Will the engineer need access indoors as well as outside?
Usually yes. The outdoor unit, the hot water cylinder, the controls and the pipework and valves indoors are all part of the visit, so allow access to each.
What should I check before booking a visit in Lochgilphead?
Note any error code on the controller, check the system pressure gauge if you have one, and make sure the outdoor unit is clear of leaves or snow. Photos of the unit and controller help.
Why is my heat pump showing an error code?
An error code is the heat pump's way of reporting a problem it has detected, such as low water flow, a sensor reading out of range or a communication fault between units. Note the code and check the manual, as some codes clear after a simple reset or pressure top-up. If it returns, an engineer can trace the underlying cause.
Why does my heat pump keep switching on and off?
Frequent starting and stopping, called short cycling, is usually caused by an oversized heat pump, low water flow, too many zones closing at once or controls set with too narrow a range. It reduces efficiency and wears components. An engineer can check the settings, flow rates and design, and can often improve it with control changes before any parts are needed.