- Area
- County Armagh
- Postcode district
- BT64
- Nation
- Northern Ireland
- Guide price
- From £90 inc VAT
- Visit
- Rate agreed in advance
Heat pump repairs for Craigavon homes
Whoever installed your heat pump, aftercare can be arranged in Craigavon. Tell us the make and model and roughly how old it is, and we will set out what the visit involves before you book.
Across Craigavon and County Armagh, refrigerant repairs on split systems are carried out by an F-gas certified engineer. Repairs in Craigavon that need a part ordered are explained and priced before the engineer leaves.
When a heat pump shows an error, loses pressure or stops heating, an engineer diagnoses the cause and explains the repair and its cost before fixing it.
- Outdoor units that have become noisy, iced up or keep switching on and off
- Heat pumps showing an error code or fault light
- Rooms or hot water not getting warm enough
What's included
- A clear explanation of the fault and a price for the repair before work goes ahead
- Refrigerant repairs by an F-gas certified engineer where needed
- Supply and fitting of replacement parts
- System refill, venting and recommissioning after the repair
- Reading of error history and operating data
We repair heat pumps in Craigavon whoever installed them, including older monobloc and split systems.
Grants and rules for heat pumps in Northern Ireland
The Boiler Upgrade Scheme covers England and Wales only, and there is currently no dedicated heat pump grant for homeowners in Northern Ireland. Our quote for a Craigavon home is therefore shown without a grant deduction; if support becomes available we will tell you how it applies.
What to budget for heat pump repairs in Craigavon
Guide prices for County Armagh, including VAT. We agree the visit rate before anyone attends, so there are no surprises on the day.
| Repair | Guide price |
|---|---|
| Fault-finding visit and diagnosis | £90–£170 |
| Sensor or thermistor replacement | £120–£270 |
| Expansion vessel or pressure relief valve | £150–£340 |
| Circulating pump replacement | £240–£470 |
| Fan motor replacement | £290–£630 |
| Refrigerant leak repair and re-gas (split systems) | £340–£920 |
| Main control board (PCB) replacement | £440–£1,050 |
Inc VAT. The fault-finding rate is agreed before we attend; repairs are priced in writing before parts are ordered.
How long is the heating season in Craigavon?
Craigavon sees roughly 7 hours 17 minutes of daylight in December and 17 hours 15 minutes in June. With a longer heating season than the south, the gains from low flow temperatures and good controls add up over the year.
Booking a visit in Craigavon
- Tell us the make if you know it, the error code or symptoms, and send photos of the unit and controller.
- We confirm the fault-finding rate and arrange a visit in Craigavon.
- The engineer diagnoses the fault and gives you a written price for the repair.
- Parts are ordered once you agree, and the repair is completed and tested.
Heat pump repairs in Craigavon: questions
How often should a heat pump in Craigavon be serviced?
Once a year is the usual recommendation, and many manufacturers make annual servicing a condition of the warranty. Check your warranty terms for the exact requirement.
Will the engineer need access indoors as well as outside?
Usually yes. The outdoor unit, the hot water cylinder, the controls and the pipework and valves indoors are all part of the visit, so allow access to each.
Do you also cover Lurgan?
Yes. We arrange heat pump servicing and repairs in Lurgan, which is about 2 miles east of Craigavon, and across County Armagh.
Can you repair a heat pump installed by another company?
Yes. We carry out fault-finding and repairs on heat pumps installed by other companies, including monobloc and split systems. Tell us the make, model and approximate age when you get in touch, plus any error code shown. If the system is still under the manufacturer's warranty, it may be quicker to contact the original installer or manufacturer first.
Why does my heat pump keep switching on and off?
Frequent starting and stopping, called short cycling, is usually caused by an oversized heat pump, low water flow, too many zones closing at once or controls set with too narrow a range. It reduces efficiency and wears components. An engineer can check the settings, flow rates and design, and can often improve it with control changes before any parts are needed.