- Area
- Greater Manchester
- Postcode district
- M26
- Nation
- England
- Guide price
- From £90 inc VAT
- Visit
- Rate agreed in advance
Before you book: heat pump repairs in Radcliffe
A heat pump that is serviced and set up properly keeps running efficiently for many years. Many heat pump faults trace back to settings, low pressure or a worn part rather than the heat pump itself, and those can usually be put right.
We repair heat pumps in Radcliffe whoever installed them, including older monobloc and split systems. Outdoor units in exposed spots around Radcliffe can ice more heavily, so siting is checked as part of any icing fault.
When a heat pump shows an error, loses pressure or stops heating, an engineer diagnoses the cause and explains the repair and its cost before fixing it.
- Rooms or hot water not getting warm enough
- Heat pumps showing an error code or fault light
- Systems losing pressure or needing frequent topping up
What's included
- Supply and fitting of replacement parts
- Reading of error history and operating data
- System refill, venting and recommissioning after the repair
- Fault-finding visit at a rate agreed before attending
- A clear explanation of the fault and a price for the repair before work goes ahead
Across Radcliffe and Greater Manchester, refrigerant repairs on split systems are carried out by an F-gas certified engineer.
Grants and rules for heat pumps in England
In England the Boiler Upgrade Scheme gives £7,500 towards an air source heat pump (£9,000 if it replaces oil or LPG, from 21 July 2026 to 31 March 2027), and since 28 April 2026 a valid EPC is no longer needed. The grant is applied for by the MCS-certified installer and shown as a deduction on your Radcliffe quote.
What to budget for heat pump repairs in Radcliffe
These are guide prices including VAT. The rate for your visit in Radcliffe is confirmed before we book it, and any repair is priced in writing before parts are ordered.
| Repair | Guide price |
|---|---|
| Fault-finding visit and diagnosis | £90–£180 |
| Sensor or thermistor replacement | £120–£270 |
| Expansion vessel or pressure relief valve | £150–£340 |
| Circulating pump replacement | £240–£470 |
| Fan motor replacement | £290–£640 |
| Refrigerant leak repair and re-gas (split systems) | £340–£930 |
| Main control board (PCB) replacement | £440–£1,100 |
Inc VAT. The fault-finding rate is agreed before we attend; repairs are priced in writing before parts are ordered.
Short winter days in Radcliffe and what they mean
Radcliffe sees roughly 7 hours 27 minutes of daylight in December and 17 hours 03 minutes in June. With a longer heating season than the south, the gains from low flow temperatures and good controls add up over the year.
How a visit works in Radcliffe
- Tell us the make if you know it, the error code or symptoms, and send photos of the unit and controller.
- We confirm the fault-finding rate and arrange a visit in Radcliffe.
- The engineer diagnoses the fault and gives you a written price for the repair.
- Parts are ordered once you agree, and the repair is completed and tested.
Heat pump repairs in Radcliffe: questions
Do you also cover Whitefield?
Yes. We arrange heat pump servicing and repairs in Whitefield, which is about a mile south-east of Radcliffe, and across Greater Manchester.
How much does a visit cost in Radcliffe?
The rate for a service or fault-finding visit is agreed before anyone attends. Any repair is priced in writing before parts are ordered, so you decide before work goes ahead.
Can you work on a heat pump in Radcliffe that someone else installed?
Yes. We arrange servicing and repairs for most air source heat pumps in Radcliffe, whoever fitted them. Tell us the make and model when you get in touch.
Why does my heat pump keep switching on and off?
Frequent starting and stopping, called short cycling, is usually caused by an oversized heat pump, low water flow, too many zones closing at once or controls set with too narrow a range. It reduces efficiency and wears components. An engineer can check the settings, flow rates and design, and can often improve it with control changes before any parts are needed.
Why is my heat pump showing an error code?
An error code is the heat pump's way of reporting a problem it has detected, such as low water flow, a sensor reading out of range or a communication fault between units. Note the code and check the manual, as some codes clear after a simple reset or pressure top-up. If it returns, an engineer can trace the underlying cause.