Typical repairs fall within a guide range of £90–£1,100, including VAT, depending on the part and the time involved. Refrigerant repairs must be done by an F-gas certified engineer. Regular heat pump servicing catches many of these faults before they stop the system working.
Repairs in Lincolnshire that need a part ordered are explained and priced before the engineer leaves. For repeated faults in Lincolnshire, the engineer looks at the system design as well as the failed part. Outdoor units in exposed spots around Lincolnshire can ice more heavily, so siting is checked as part of any icing fault.
Who it suits
- Heat pumps installed by another company that need a second opinion
- Outdoor units that have become noisy, iced up or keep switching on and off
- Systems losing pressure or needing frequent topping up
- Heat pumps showing an error code or fault light
Grants and rules for heat pumps in England
In England the Boiler Upgrade Scheme gives £7,500 towards an air source heat pump (£9,000 if it replaces oil or LPG, from 21 July 2026 to 31 March 2027), and since 28 April 2026 a valid EPC is no longer needed. The grant is applied for by the MCS-certified installer and shown as a deduction on your quote.
Heat pump repairs prices in Lincolnshire
These are guide prices including VAT. The rate for your visit in Lincolnshire is confirmed before we book it, and any repair is priced in writing before parts are ordered.
| Repair | Guide price |
|---|---|
| Fault-finding visit and diagnosis | £90–£180 |
| Sensor or thermistor replacement | £120–£280 |
| Expansion vessel or pressure relief valve | £150–£350 |
| Circulating pump replacement | £250–£480 |
| Fan motor replacement | £300–£650 |
| Refrigerant leak repair and re-gas (split systems) | £350–£950 |
| Main control board (PCB) replacement | £450–£1,100 |
Inc VAT. The fault-finding rate is agreed before we attend; repairs are priced in writing before parts are ordered.
Towns we cover in Lincolnshire
We cover 14 towns in Lincolnshire for heat pump repairs. Each links to local guide prices and the grant position for England.
| Town | Postcode district | Nearest town | Midwinter daylight |
|---|---|---|---|
| Lincoln | LN6 | Gainsborough | 7 h 31 min |
| Grimsby | DN32 | Cleethorpes | 7 h 27 min |
| Scunthorpe | DN16 | Brough | 7 h 27 min |
| Boston | PE21 | Spalding | 7 h 34 min |
| Grantham | NG31 | Sleaford | 7 h 35 min |
| Cleethorpes | DN35 | Grimsby | 7 h 27 min |
| Spalding | PE11 | Bourne | 7 h 36 min |
| Skegness | PE25 | Boston | 7 h 32 min |
| Stamford | PE9 | Bourne | 7 h 37 min |
| Gainsborough | DN21 | Retford | 7 h 29 min |
| Louth | LN11 | Horncastle | 7 h 29 min |
| Sleaford | NG34 | Grantham | 7 h 34 min |
| Bourne | PE10 | Stamford | 7 h 36 min |
| Horncastle | LN9 | Louth | 7 h 31 min |
Heat pump repairs questions
Do refrigerant repairs need a specialist?
Yes. Any work on a heat pump's refrigerant circuit, such as tracing a leak, replacing a component or re-gassing, must by law be done by an F-gas certified engineer where the refrigerant is fluorinated, such as R32; units using R290 (propane) need an engineer trained in flammable refrigerants. On split systems the refrigerant runs through pipes inside your home, so leaks there are more likely than on sealed monobloc units.
Is ice on my heat pump a fault?
Some frost on the outdoor unit in cold, damp weather is normal, and the unit clears it with regular defrost cycles, often releasing a little vapour. It becomes a fault when thick ice builds up and does not clear, or when ice blocks the fan. That can point to poor airflow, a failed sensor, drainage problems or low refrigerant, and needs checking.
Why does my heat pump keep switching on and off?
Frequent starting and stopping, called short cycling, is usually caused by an oversized heat pump, low water flow, too many zones closing at once or controls set with too narrow a range. It reduces efficiency and wears components. An engineer can check the settings, flow rates and design, and can often improve it with control changes before any parts are needed.
Why is my heat pump showing an error code?
An error code is the heat pump's way of reporting a problem it has detected, such as low water flow, a sensor reading out of range or a communication fault between units. Note the code and check the manual, as some codes clear after a simple reset or pressure top-up. If it returns, an engineer can trace the underlying cause.