- Area
- Oxfordshire
- Postcode district
- OX11
- Nation
- England
- Guide price
- From £90 inc VAT
- Visit
- Rate agreed in advance
Before you book: heat pump repairs in Didcot
A heat pump that is serviced and set up properly keeps running efficiently for many years. Many heat pump faults trace back to settings, low pressure or a worn part rather than the heat pump itself, and those can usually be put right.
Heat pump owners in Didcot can arrange a fault-finding visit at a rate agreed before an engineer attends. For repeated faults in Didcot, the engineer looks at the system design as well as the failed part.
When a heat pump shows an error, loses pressure or stops heating, an engineer diagnoses the cause and explains the repair and its cost before fixing it.
- Systems losing pressure or needing frequent topping up
- Rooms or hot water not getting warm enough
- Heat pumps installed by another company that need a second opinion
What's included
- Reading of error history and operating data
- Testing of sensors, pumps, valves, pressures and electrics
- System refill, venting and recommissioning after the repair
- Supply and fitting of replacement parts
- Fault-finding visit at a rate agreed before attending
We repair heat pumps in Didcot whoever installed them, including older monobloc and split systems.
Grants and rules for heat pumps in England
In England the Boiler Upgrade Scheme gives £7,500 towards an air source heat pump (£9,000 if it replaces oil or LPG, from 21 July 2026 to 31 March 2027), and since 28 April 2026 a valid EPC is no longer needed. The grant is applied for by the MCS-certified installer and shown as a deduction on your Didcot quote.
Heat pump repairs prices in Didcot
Guide prices for Oxfordshire, including VAT. We agree the visit rate before anyone attends, so there are no surprises on the day.
| Repair | Guide price |
|---|---|
| Fault-finding visit and diagnosis | £90–£190 |
| Sensor or thermistor replacement | £120–£290 |
| Expansion vessel or pressure relief valve | £160–£360 |
| Circulating pump replacement | £260–£500 |
| Fan motor replacement | £310–£680 |
| Refrigerant leak repair and re-gas (split systems) | £360–£990 |
| Main control board (PCB) replacement | £470–£1,150 |
Inc VAT. The fault-finding rate is agreed before we attend; repairs are priced in writing before parts are ordered.
Winter daylight and heating in Didcot
On the shortest day Didcot gets about 7 hours 48 minutes of daylight, with the noon sun around 15° up. The heating season runs from autumn into spring, so a heat pump that is sized correctly and set up with weather compensation does most of its work in steady, cool conditions.
Booking a visit in Didcot
- Tell us the make if you know it, the error code or symptoms, and send photos of the unit and controller.
- We confirm the fault-finding rate and arrange a visit in Didcot.
- The engineer diagnoses the fault and gives you a written price for the repair.
- Parts are ordered once you agree, and the repair is completed and tested.
Heat pump repairs in Didcot: questions
Can you work on a heat pump in Didcot that someone else installed?
Yes. We arrange servicing and repairs for most air source heat pumps in Didcot, whoever fitted them. Tell us the make and model when you get in touch.
Will the engineer need access indoors as well as outside?
Usually yes. The outdoor unit, the hot water cylinder, the controls and the pipework and valves indoors are all part of the visit, so allow access to each.
What should I check before booking a visit in Didcot?
Note any error code on the controller, check the system pressure gauge if you have one, and make sure the outdoor unit is clear of leaves or snow. Photos of the unit and controller help.
Is ice on my heat pump a fault?
Some frost on the outdoor unit in cold, damp weather is normal, and the unit clears it with regular defrost cycles, often releasing a little vapour. It becomes a fault when thick ice builds up and does not clear, or when ice blocks the fan. That can point to poor airflow, a failed sensor, drainage problems or low refrigerant, and needs checking.
Why does my heat pump keep switching on and off?
Frequent starting and stopping, called short cycling, is usually caused by an oversized heat pump, low water flow, too many zones closing at once or controls set with too narrow a range. It reduces efficiency and wears components. An engineer can check the settings, flow rates and design, and can often improve it with control changes before any parts are needed.