- Area
- Warwickshire
- Postcode district
- CV36
- Nation
- England
- Guide price
- From £90 inc VAT
- Visit
- Rate agreed in advance
What to know about heat pump repairs in Shipston-on-Stour
A heat pump that is serviced and set up properly keeps running efficiently for many years. Many heat pump faults trace back to settings, low pressure or a worn part rather than the heat pump itself, and those can usually be put right.
Heat pump owners in Shipston-on-Stour can arrange a fault-finding visit at a rate agreed before an engineer attends. Repairs in Shipston-on-Stour that need a part ordered are explained and priced before the engineer leaves.
When a heat pump shows an error, loses pressure or stops heating, an engineer diagnoses the cause and explains the repair and its cost before fixing it.
- Outdoor units that have become noisy, iced up or keep switching on and off
- Heat pumps showing an error code or fault light
- Heat pumps installed by another company that need a second opinion
What's included
- System refill, venting and recommissioning after the repair
- Testing of sensors, pumps, valves, pressures and electrics
- A clear explanation of the fault and a price for the repair before work goes ahead
- Refrigerant repairs by an F-gas certified engineer where needed
- Supply and fitting of replacement parts
Outdoor units in exposed spots around Shipston-on-Stour can ice more heavily, so siting is checked as part of any icing fault.
Grants and rules for heat pumps in England
Homes in Shipston-on-Stour can use the Boiler Upgrade Scheme, which takes £7,500 off the cost of an air source heat pump when it replaces fossil-fuel or electric heating. Replacing oil or LPG heating qualifies for £9,000 for installations from 21 July 2026 to 31 March 2027, and air-to-air systems for £2,500. The MCS-certified installer named in your quote applies for the grant and deducts it from the price.
Heat pump repairs prices in Shipston-on-Stour
These are guide prices including VAT. The rate for your visit in Shipston-on-Stour is confirmed before we book it, and any repair is priced in writing before parts are ordered.
| Repair | Guide price |
|---|---|
| Fault-finding visit and diagnosis | £90–£180 |
| Sensor or thermistor replacement | £120–£280 |
| Expansion vessel or pressure relief valve | £150–£350 |
| Circulating pump replacement | £250–£480 |
| Fan motor replacement | £300–£650 |
| Refrigerant leak repair and re-gas (split systems) | £350–£950 |
| Main control board (PCB) replacement | £450–£1,100 |
Inc VAT. The fault-finding rate is agreed before we attend; repairs are priced in writing before parts are ordered.
Designing for Shipston-on-Stour's winters
Shipston-on-Stour has about 7 hours 44 minutes of daylight at midwinter and 16 hours 45 minutes at midsummer. That swing matters if you pair a heat pump with solar panels: summer generation can cover much of the hot water, winter generation far less.
How a visit works in Shipston-on-Stour
- Tell us the make if you know it, the error code or symptoms, and send photos of the unit and controller.
- We confirm the fault-finding rate and arrange a visit in Shipston-on-Stour.
- The engineer diagnoses the fault and gives you a written price for the repair.
- Parts are ordered once you agree, and the repair is completed and tested.
Heat pump repairs in Shipston-on-Stour: questions
Can you work on a heat pump in Shipston-on-Stour that someone else installed?
Yes. We arrange servicing and repairs for most air source heat pumps in Shipston-on-Stour, whoever fitted them. Tell us the make and model when you get in touch.
Will the engineer need access indoors as well as outside?
Usually yes. The outdoor unit, the hot water cylinder, the controls and the pipework and valves indoors are all part of the visit, so allow access to each.
How much does a visit cost in Shipston-on-Stour?
The rate for a service or fault-finding visit is agreed before anyone attends. Any repair is priced in writing before parts are ordered, so you decide before work goes ahead.
Why is my heat pump showing an error code?
An error code is the heat pump's way of reporting a problem it has detected, such as low water flow, a sensor reading out of range or a communication fault between units. Note the code and check the manual, as some codes clear after a simple reset or pressure top-up. If it returns, an engineer can trace the underlying cause.
Why does my heat pump keep switching on and off?
Frequent starting and stopping, called short cycling, is usually caused by an oversized heat pump, low water flow, too many zones closing at once or controls set with too narrow a range. It reduces efficiency and wears components. An engineer can check the settings, flow rates and design, and can often improve it with control changes before any parts are needed.