- Area
- West Sussex
- Postcode district
- GU29
- Nation
- England
- Guide price
- From £90 inc VAT
- Visit
- Rate agreed in advance
Heat pump repairs for Midhurst homes
Whoever installed your heat pump, aftercare can be arranged in Midhurst. Tell us the make and model and roughly how old it is, and we will set out what the visit involves before you book.
For repeated faults in Midhurst, the engineer looks at the system design as well as the failed part. We repair heat pumps in Midhurst whoever installed them, including older monobloc and split systems.
When a heat pump shows an error, loses pressure or stops heating, an engineer diagnoses the cause and explains the repair and its cost before fixing it.
- Heat pumps showing an error code or fault light
- Heat pumps installed by another company that need a second opinion
- Rooms or hot water not getting warm enough
What's included
- System refill, venting and recommissioning after the repair
- Testing of sensors, pumps, valves, pressures and electrics
- Fault-finding visit at a rate agreed before attending
- Supply and fitting of replacement parts
- Reading of error history and operating data
Repairs in Midhurst that need a part ordered are explained and priced before the engineer leaves.
Grants and rules for heat pumps in England
In England the Boiler Upgrade Scheme gives £7,500 towards an air source heat pump (£9,000 if it replaces oil or LPG, from 21 July 2026 to 31 March 2027), and since 28 April 2026 a valid EPC is no longer needed. The grant is applied for by the MCS-certified installer and shown as a deduction on your Midhurst quote.
What to budget for heat pump repairs in Midhurst
Guide prices for West Sussex, including VAT. We agree the visit rate before anyone attends, so there are no surprises on the day.
| Repair | Guide price |
|---|---|
| Fault-finding visit and diagnosis | £90–£190 |
| Sensor or thermistor replacement | £120–£290 |
| Expansion vessel or pressure relief valve | £160–£360 |
| Circulating pump replacement | £260–£500 |
| Fan motor replacement | £310–£680 |
| Refrigerant leak repair and re-gas (split systems) | £360–£990 |
| Main control board (PCB) replacement | £470–£1,150 |
Inc VAT. The fault-finding rate is agreed before we attend; repairs are priced in writing before parts are ordered.
How long is the heating season in Midhurst?
On the shortest day Midhurst gets about 7 hours 55 minutes of daylight, and the winter sun reaches only around 16° above the horizon at noon. Winters this far south are milder than in most of the UK, which helps a heat pump run at low flow temperatures for much of the season.
How a visit works in Midhurst
- Tell us the make if you know it, the error code or symptoms, and send photos of the unit and controller.
- We confirm the fault-finding rate and arrange a visit in Midhurst.
- The engineer diagnoses the fault and gives you a written price for the repair.
- Parts are ordered once you agree, and the repair is completed and tested.
Heat pump repairs in Midhurst: questions
Will the engineer need access indoors as well as outside?
Usually yes. The outdoor unit, the hot water cylinder, the controls and the pipework and valves indoors are all part of the visit, so allow access to each.
Can you work on a heat pump in Midhurst that someone else installed?
Yes. We arrange servicing and repairs for most air source heat pumps in Midhurst, whoever fitted them. Tell us the make and model when you get in touch.
What should I check before booking a visit in Midhurst?
Note any error code on the controller, check the system pressure gauge if you have one, and make sure the outdoor unit is clear of leaves or snow. Photos of the unit and controller help.
Why does my heat pump keep switching on and off?
Frequent starting and stopping, called short cycling, is usually caused by an oversized heat pump, low water flow, too many zones closing at once or controls set with too narrow a range. It reduces efficiency and wears components. An engineer can check the settings, flow rates and design, and can often improve it with control changes before any parts are needed.
Why is my heat pump showing an error code?
An error code is the heat pump's way of reporting a problem it has detected, such as low water flow, a sensor reading out of range or a communication fault between units. Note the code and check the manual, as some codes clear after a simple reset or pressure top-up. If it returns, an engineer can trace the underlying cause.