- Area
- North Yorkshire
- Postcode district
- TS1
- Nation
- England
- Guide price
- Priced after survey
- Survey
- Free for installation enquiries
Before you book: heat loss surveys in Middlesbrough
Most homes can run on a heat pump if the system is designed properly, and Middlesbrough is no different. The key is matching the heat pump and radiators to the home's heat loss.
Houses in Middlesbrough built in different eras can need very different heat pump sizes, which is why each is calculated room by room. For Middlesbrough homes with extensions or loft conversions, each part of the house is assessed on its own construction.
Every heat pump we quote starts with a room-by-room heat loss survey, free with installation enquiries and also available as a stand-alone report.
- Anyone getting a heat pump quote, as the first step
- Landlords comparing properties before deciding where to switch first
- Homes with an existing heat pump that seems undersized or expensive to run
What's included
- Electrical supply and network operator notes
- Recommended heat pump size and design flow temperature
- Outdoor unit siting options and noise check
- Radiator schedule with any upgrades needed for each room
- Room-by-room heat loss calculation using the MCS method
A surveyor visits your Middlesbrough home to measure each room, window and wall before any heat pump is sized.
Grants and rules for heat pumps in England
Homes in Middlesbrough can use the Boiler Upgrade Scheme, which takes £7,500 off the cost of an air source heat pump when it replaces fossil-fuel or electric heating. Replacing oil or LPG heating qualifies for £9,000 for installations from 21 July 2026 to 31 March 2027, and air-to-air systems for £2,500. The MCS-certified installer named in your quote applies for the grant and deducts it from the price.
Installing heat pumps is zero-rated for VAT across the UK until 31 March 2027. Since 29 May 2025, permitted development in England allows up to two air source heat pumps on a house, each up to 1.5 m³, with no blanket 1 m boundary rule — the installation must still meet the MCS planning standards, including the noise check. Listed buildings, flats and some conservation-area positions need extra consent, which we check at survey.
Heat loss survey costs around Middlesbrough
The ranges below are typical installed prices for homes in North Yorkshire, including VAT. A survey sets the exact figure, because two similar-looking houses in Middlesbrough can need quite different radiators and pipework.
| Survey | Guide price |
|---|---|
| Home survey and heat loss calculation with an installation quote | Free |
| Stand-alone heat loss survey and report | £150–£400 |
Inc VAT. A stand-alone report is for homeowners who want the design without an installation quote.
Winter daylight and heating in Middlesbrough
Middlesbrough sees roughly 7 hours 15 minutes of daylight in December and 17 hours 16 minutes in June. With a longer heating season than the south, the gains from low flow temperatures and good controls add up over the year.
How installation works in Middlesbrough
- Start online with a guide price or call us.
- A home survey in Middlesbrough gives us the room-by-room heat loss.
- Your written quote sets out the design, the price and the grant position where you live.
- Installation is booked for dates that suit you; most homes take 2–4 days on site.
- After commissioning you get a handover of the controls and settings, plus the certificates.
Heat loss surveys in Middlesbrough: questions
Do you cover Thornaby-on-Tees as well as Middlesbrough?
Yes. We arrange surveys and installation in Thornaby-on-Tees, which is about 4 miles south-west of Middlesbrough, and across North Yorkshire.
Where would the outdoor unit go on a Middlesbrough house?
Usually at the side or rear, on a level base with space around it for airflow and servicing, away from bedroom windows where possible. The surveyor checks positions at your Middlesbrough home.
How long does installation take in Middlesbrough?
Most installations take 2–4 days on site. Jobs with several radiator changes or new pipework take longer, and your quote for a Middlesbrough home states the expected time.
Why can't you size the heat pump from my boiler?
Boilers are often much larger than a home's real heat loss, because they are sized for fast hot water and quick warm-ups. Matching a heat pump to the boiler's output usually means an oversized unit that costs more and switches on and off too often. A room-by-room calculation finds the actual heat demand, which is what the heat pump needs to meet.
What is a design flow temperature?
The design flow temperature is the temperature of the water sent to your radiators or underfloor heating on the coldest design day. Heat pumps are more efficient at lower flow temperatures, typically around 35–50°C. Choosing it is a balance: a lower figure improves efficiency but can mean larger radiators in some rooms, so the design shows both.