A heat pump hot water cylinder is an insulated tank that stores hot water heated by the heat pump, with a much larger internal coil than a cylinder designed for a boiler. Heat pumps heat water to a lower temperature than boilers, typically around 45–55°C, so a bigger coil is needed to pass heat into the stored water quickly. A standard boiler cylinder would heat slowly and make the heat pump work harder than it should.
In terraced homes around Cheshire and across Cheshire, slimline cylinders can fit spaces a standard model cannot. Many homes in Cheshire with combi boilers have no airing cupboard, so the survey looks for the most practical cylinder space. Discharge pipe routes are planned at the survey so a Cheshire cylinder can drain safely to the outside.
Who it suits
- Larger families or homes with two or more bathrooms
- Households with older vented cylinders and loft tanks who want mains-pressure showers
- Homes replacing a combi boiler that need space found for a cylinder
- Homes with solar PV that want to store daytime electricity as hot water
Grants and rules for heat pumps in England
Homes in Cheshire can use the Boiler Upgrade Scheme, which takes £7,500 off the cost of an air source heat pump when it replaces fossil-fuel or electric heating. Replacing oil or LPG heating qualifies for £9,000 for installations from 21 July 2026 to 31 March 2027, and air-to-air systems for £2,500. The MCS-certified installer named in your quote applies for the grant and deducts it from the price.
Installing heat pumps is zero-rated for VAT across the UK until 31 March 2027. Since 29 May 2025, permitted development in England allows up to two air source heat pumps on a house, each up to 1.5 m³, with no blanket 1 m boundary rule — the installation must still meet the MCS planning standards, including the noise check. Listed buildings, flats and some conservation-area positions need extra consent, which we check at survey.
Heat pump hot water cylinders prices in Cheshire
Here are typical prices for heat pump hot water cylinders in Cheshire, installed and including VAT. Use the guide price tool for a figure based on your home, then a survey confirms it in writing.
| Work | Guide price |
|---|---|
| Heat pump hot water cylinder (supplied and fitted) | £1,200–£2,200 |
Supplied and fitted, inc VAT. Included in every full system price.
Towns we cover in Cheshire
We cover 18 towns in Cheshire for heat pump hot water cylinders. Each links to local guide prices and the grant position for England.
| Town | Postcode district | Nearest town | Midwinter daylight |
|---|---|---|---|
| Warrington | WA1 | Widnes | 7 h 29 min |
| Chester | CH1 | Ellesmere Port | 7 h 31 min |
| Crewe | CW1 | Nantwich | 7 h 33 min |
| Ellesmere Port | CH65 | Chester | 7 h 30 min |
| Widnes | WA8 | Runcorn | 7 h 30 min |
| Runcorn | WA7 | Widnes | 7 h 30 min |
| Macclesfield | SK11 | Alderley Edge | 7 h 31 min |
| Northwich | CW9 | Winsford | 7 h 31 min |
| Winsford | CW7 | Middlewich | 7 h 31 min |
| Congleton | CW12 | Sandbach | 7 h 32 min |
| Wilmslow | SK9 | Alderley Edge | 7 h 30 min |
| Sandbach | CW11 | Crewe | 7 h 32 min |
| Nantwich | CW5 | Crewe | 7 h 33 min |
| Alderley Edge | SK9 | Wilmslow | 7 h 30 min |
| Frodsham | WA6 | Runcorn | 7 h 30 min |
| Knutsford | WA16 | Alderley Edge | 7 h 30 min |
| Middlewich | CW10 | Winsford | 7 h 31 min |
| Tarporley | CW6 | Winsford | 7 h 32 min |
Heat pump hot water cylinders questions
I have a combi boiler. Where will the cylinder go?
Moving from a combi to a heat pump means finding space for a cylinder, usually somewhere around 600 mm square and up to about 2 m tall. Common choices are a bedroom or landing cupboard, a utility room, under the stairs or an integral garage. The surveyor looks at your layout and suggests options, including slimline models where space is tight.
Can I keep my existing hot water cylinder with a heat pump?
Usually not. Cylinders designed for boilers have a small coil that cannot transfer heat quickly at heat pump temperatures, so the water would reheat slowly and efficiency would suffer. A heat pump cylinder has a much larger coil. The new cylinder can often go in the same cupboard, though, if there is enough height and floor space.
How much does a heat pump cylinder cost?
A heat pump hot water cylinder has a guide price of £1,200–£2,200, installed and including VAT. In a full heat pump installation the cylinder is already included in the system guide price, so this figure mainly applies where a cylinder is replaced on its own. Capacity, coil design and the pipework needed affect where your price sits.
Do I need good water pressure for an unvented cylinder?
Yes. An unvented cylinder runs at mains pressure, so it needs enough incoming pressure and flow to supply your taps and showers well. We measure your mains supply at the survey. If flow is low, options include a different cylinder type or an upgrade to the incoming supply pipe, which we explain before you commit.