- Area
- Devon
- Postcode district
- EX39
- Nation
- England
- Guide price
- From £90 inc VAT
- Visit
- Rate agreed in advance
What to know about heat pump repairs in Bideford
Aftercare matters as much as installation. For a heat pump in Bideford the visit checks the outdoor unit, the water circuit and the controls, and the engineer explains any settings that would help the system run more efficiently.
Heat pump owners in Bideford can arrange a fault-finding visit at a rate agreed before an engineer attends. Across Bideford and Devon, refrigerant repairs on split systems are carried out by an F-gas certified engineer.
When a heat pump shows an error, loses pressure or stops heating, an engineer diagnoses the cause and explains the repair and its cost before fixing it.
- Heat pumps installed by another company that need a second opinion
- Heat pumps showing an error code or fault light
- Rooms or hot water not getting warm enough
What's included
- Reading of error history and operating data
- Testing of sensors, pumps, valves, pressures and electrics
- Refrigerant repairs by an F-gas certified engineer where needed
- Supply and fitting of replacement parts
- A clear explanation of the fault and a price for the repair before work goes ahead
We repair heat pumps in Bideford whoever installed them, including older monobloc and split systems.
Grants and rules for heat pumps in England
In England the Boiler Upgrade Scheme gives £7,500 towards an air source heat pump (£9,000 if it replaces oil or LPG, from 21 July 2026 to 31 March 2027), and since 28 April 2026 a valid EPC is no longer needed. The grant is applied for by the MCS-certified installer and shown as a deduction on your Bideford quote.
What to budget for heat pump repairs in Bideford
These are guide prices including VAT. The rate for your visit in Bideford is confirmed before we book it, and any repair is priced in writing before parts are ordered.
| Repair | Guide price |
|---|---|
| Fault-finding visit and diagnosis | £90–£180 |
| Sensor or thermistor replacement | £120–£280 |
| Expansion vessel or pressure relief valve | £150–£350 |
| Circulating pump replacement | £250–£480 |
| Fan motor replacement | £300–£660 |
| Refrigerant leak repair and re-gas (split systems) | £350–£960 |
| Main control board (PCB) replacement | £450–£1,100 |
Inc VAT. The fault-finding rate is agreed before we attend; repairs are priced in writing before parts are ordered.
How long is the heating season in Bideford?
Bideford sees roughly 7 hours 54 minutes of daylight in late December against 16 hours 33 minutes in June. Milder southern winters suit heat pumps well, though the system is still sized for a cold snap rather than an average day.
Booking a visit in Bideford
- Tell us the make if you know it, the error code or symptoms, and send photos of the unit and controller.
- We confirm the fault-finding rate and arrange a visit in Bideford.
- The engineer diagnoses the fault and gives you a written price for the repair.
- Parts are ordered once you agree, and the repair is completed and tested.
Heat pump repairs in Bideford: questions
How often should a heat pump in Bideford be serviced?
Once a year is the usual recommendation, and many manufacturers make annual servicing a condition of the warranty. Check your warranty terms for the exact requirement.
Can you work on a heat pump in Bideford that someone else installed?
Yes. We arrange servicing and repairs for most air source heat pumps in Bideford, whoever fitted them. Tell us the make and model when you get in touch.
What should I check before booking a visit in Bideford?
Note any error code on the controller, check the system pressure gauge if you have one, and make sure the outdoor unit is clear of leaves or snow. Photos of the unit and controller help.
Why is my heat pump showing an error code?
An error code is the heat pump's way of reporting a problem it has detected, such as low water flow, a sensor reading out of range or a communication fault between units. Note the code and check the manual, as some codes clear after a simple reset or pressure top-up. If it returns, an engineer can trace the underlying cause.
Do refrigerant repairs need a specialist?
Yes. Any work on a heat pump's refrigerant circuit, such as tracing a leak, replacing a component or re-gassing, must by law be done by an F-gas certified engineer where the refrigerant is fluorinated, such as R32; units using R290 (propane) need an engineer trained in flammable refrigerants. On split systems the refrigerant runs through pipes inside your home, so leaks there are more likely than on sealed monobloc units.