- Area
- Dyfed
- Postcode district
- SA48
- Nation
- Wales
- Guide price
- From £90 inc VAT
- Visit
- Rate agreed in advance
Before you book: heat pump repairs in Lampeter
Aftercare matters as much as installation. For a heat pump in Lampeter the visit checks the outdoor unit, the water circuit and the controls, and the engineer explains any settings that would help the system run more efficiently.
Outdoor units in exposed spots around Lampeter can ice more heavily, so siting is checked as part of any icing fault. Heat pump owners in Lampeter can arrange a fault-finding visit at a rate agreed before an engineer attends.
When a heat pump shows an error, loses pressure or stops heating, an engineer diagnoses the cause and explains the repair and its cost before fixing it.
- Rooms or hot water not getting warm enough
- Outdoor units that have become noisy, iced up or keep switching on and off
- Systems losing pressure or needing frequent topping up
What's included
- Fault-finding visit at a rate agreed before attending
- Refrigerant repairs by an F-gas certified engineer where needed
- System refill, venting and recommissioning after the repair
- Supply and fitting of replacement parts
- A clear explanation of the fault and a price for the repair before work goes ahead
We repair heat pumps in Lampeter whoever installed them, including older monobloc and split systems.
Grants and rules for heat pumps in Wales
In Wales the Boiler Upgrade Scheme gives £7,500 towards an air source heat pump (£9,000 if it replaces oil or LPG, from 21 July 2026 to 31 March 2027; £2,500 for air-to-air). The MCS-certified installer named in your quote applies to Ofgem for you, and the grant comes off your Lampeter quote.
Heat pump repairs prices in Lampeter
Guide prices for Dyfed, including VAT. We agree the visit rate before anyone attends, so there are no surprises on the day.
| Repair | Guide price |
|---|---|
| Fault-finding visit and diagnosis | £90–£180 |
| Sensor or thermistor replacement | £120–£280 |
| Expansion vessel or pressure relief valve | £150–£350 |
| Circulating pump replacement | £250–£480 |
| Fan motor replacement | £300–£650 |
| Refrigerant leak repair and re-gas (split systems) | £350–£950 |
| Main control board (PCB) replacement | £450–£1,100 |
Inc VAT. The fault-finding rate is agreed before we attend; repairs are priced in writing before parts are ordered.
Winter daylight and heating in Lampeter
On the shortest day Lampeter gets about 7 hours 43 minutes of daylight, with the noon sun around 14° up. The heating season runs from autumn into spring, so a heat pump that is sized correctly and set up with weather compensation does most of its work in steady, cool conditions.
What happens when you book in Lampeter?
- Tell us the make if you know it, the error code or symptoms, and send photos of the unit and controller.
- We confirm the fault-finding rate and arrange a visit in Lampeter.
- The engineer diagnoses the fault and gives you a written price for the repair.
- Parts are ordered once you agree, and the repair is completed and tested.
Heat pump repairs in Lampeter: questions
What should I check before booking a visit in Lampeter?
Note any error code on the controller, check the system pressure gauge if you have one, and make sure the outdoor unit is clear of leaves or snow. Photos of the unit and controller help.
Do you also cover Carmarthen?
Yes. We arrange heat pump servicing and repairs in Carmarthen, which is about 20 miles south-west of Lampeter, and across Dyfed.
Can you work on a heat pump in Lampeter that someone else installed?
Yes. We arrange servicing and repairs for most air source heat pumps in Lampeter, whoever fitted them. Tell us the make and model when you get in touch.
How much does a heat pump repair cost?
Heat pump repairs have a typical range of £90–£1,100, including VAT, depending on the part and labour involved. Sensor replacements sit at the lower end, while control boards and refrigerant repairs on split systems sit higher. Every repair starts with a fault-finding visit, with a guide price of £90–£180 for the first hour, and the repair is priced before work goes ahead.
Why does my heat pump keep switching on and off?
Frequent starting and stopping, called short cycling, is usually caused by an oversized heat pump, low water flow, too many zones closing at once or controls set with too narrow a range. It reduces efficiency and wears components. An engineer can check the settings, flow rates and design, and can often improve it with control changes before any parts are needed.