- Area
- Gloucestershire
- Postcode district
- GL7
- Nation
- England
- Guide price
- From £90 inc VAT
- Visit
- Rate agreed in advance
Before you book: heat pump repairs in Cirencester
Aftercare matters as much as installation. For a heat pump in Cirencester the visit checks the outdoor unit, the water circuit and the controls, and the engineer explains any settings that would help the system run more efficiently.
Repairs in Cirencester that need a part ordered are explained and priced before the engineer leaves. Heat pump owners in Cirencester can arrange a fault-finding visit at a rate agreed before an engineer attends.
When a heat pump shows an error, loses pressure or stops heating, an engineer diagnoses the cause and explains the repair and its cost before fixing it.
- Heat pumps installed by another company that need a second opinion
- Rooms or hot water not getting warm enough
- Heat pumps showing an error code or fault light
What's included
- Reading of error history and operating data
- Refrigerant repairs by an F-gas certified engineer where needed
- Fault-finding visit at a rate agreed before attending
- Testing of sensors, pumps, valves, pressures and electrics
- Supply and fitting of replacement parts
Outdoor units in exposed spots around Cirencester can ice more heavily, so siting is checked as part of any icing fault.
Grants and rules for heat pumps in England
In England the Boiler Upgrade Scheme gives £7,500 towards an air source heat pump (£9,000 if it replaces oil or LPG, from 21 July 2026 to 31 March 2027), and since 28 April 2026 a valid EPC is no longer needed. The grant is applied for by the MCS-certified installer and shown as a deduction on your Cirencester quote.
What to budget for heat pump repairs in Cirencester
Guide prices for Gloucestershire, including VAT. We agree the visit rate before anyone attends, so there are no surprises on the day.
| Repair | Guide price |
|---|---|
| Fault-finding visit and diagnosis | £90–£180 |
| Sensor or thermistor replacement | £120–£280 |
| Expansion vessel or pressure relief valve | £150–£350 |
| Circulating pump replacement | £250–£480 |
| Fan motor replacement | £300–£660 |
| Refrigerant leak repair and re-gas (split systems) | £350–£960 |
| Main control board (PCB) replacement | £450–£1,100 |
Inc VAT. The fault-finding rate is agreed before we attend; repairs are priced in writing before parts are ordered.
Winter daylight and heating in Cirencester
On the shortest day Cirencester gets about 7 hours 47 minutes of daylight, with the noon sun around 15° up. The heating season runs from autumn into spring, so a heat pump that is sized correctly and set up with weather compensation does most of its work in steady, cool conditions.
How a visit works in Cirencester
- Tell us the make if you know it, the error code or symptoms, and send photos of the unit and controller.
- We confirm the fault-finding rate and arrange a visit in Cirencester.
- The engineer diagnoses the fault and gives you a written price for the repair.
- Parts are ordered once you agree, and the repair is completed and tested.
Heat pump repairs in Cirencester: questions
Do you also cover Stroud?
Yes. We arrange heat pump servicing and repairs in Stroud, which is about 10 miles west of Cirencester, and across Gloucestershire.
Will the engineer need access indoors as well as outside?
Usually yes. The outdoor unit, the hot water cylinder, the controls and the pipework and valves indoors are all part of the visit, so allow access to each.
How much does a visit cost in Cirencester?
The rate for a service or fault-finding visit is agreed before anyone attends. Any repair is priced in writing before parts are ordered, so you decide before work goes ahead.
Why is my heat pump showing an error code?
An error code is the heat pump's way of reporting a problem it has detected, such as low water flow, a sensor reading out of range or a communication fault between units. Note the code and check the manual, as some codes clear after a simple reset or pressure top-up. If it returns, an engineer can trace the underlying cause.
Do refrigerant repairs need a specialist?
Yes. Any work on a heat pump's refrigerant circuit, such as tracing a leak, replacing a component or re-gassing, must by law be done by an F-gas certified engineer where the refrigerant is fluorinated, such as R32; units using R290 (propane) need an engineer trained in flammable refrigerants. On split systems the refrigerant runs through pipes inside your home, so leaks there are more likely than on sealed monobloc units.