- Area
- Mid Glamorgan
- Postcode district
- CF31
- Nation
- Wales
- Guide price
- From £90 inc VAT
- Visit
- Rate agreed in advance
Before you book: heat pump repairs in Bridgend
Whoever installed your heat pump, aftercare can be arranged in Bridgend. Tell us the make and model and roughly how old it is, and we will set out what the visit involves before you book.
For repeated faults in Bridgend, the engineer looks at the system design as well as the failed part. Repairs in Bridgend that need a part ordered are explained and priced before the engineer leaves.
When a heat pump shows an error, loses pressure or stops heating, an engineer diagnoses the cause and explains the repair and its cost before fixing it.
- Heat pumps installed by another company that need a second opinion
- Rooms or hot water not getting warm enough
- Systems losing pressure or needing frequent topping up
What's included
- Refrigerant repairs by an F-gas certified engineer where needed
- Fault-finding visit at a rate agreed before attending
- A clear explanation of the fault and a price for the repair before work goes ahead
- Reading of error history and operating data
- Supply and fitting of replacement parts
Across Bridgend and Mid Glamorgan, refrigerant repairs on split systems are carried out by an F-gas certified engineer.
Grants and rules for heat pumps in Wales
In Wales the Boiler Upgrade Scheme gives £7,500 towards an air source heat pump (£9,000 if it replaces oil or LPG, from 21 July 2026 to 31 March 2027; £2,500 for air-to-air). The MCS-certified installer named in your quote applies to Ofgem for you, and the grant comes off your Bridgend quote.
What to budget for heat pump repairs in Bridgend
These are guide prices including VAT. The rate for your visit in Bridgend is confirmed before we book it, and any repair is priced in writing before parts are ordered.
| Repair | Guide price |
|---|---|
| Fault-finding visit and diagnosis | £90–£180 |
| Sensor or thermistor replacement | £120–£280 |
| Expansion vessel or pressure relief valve | £150–£350 |
| Circulating pump replacement | £250–£480 |
| Fan motor replacement | £300–£650 |
| Refrigerant leak repair and re-gas (split systems) | £350–£950 |
| Main control board (PCB) replacement | £450–£1,100 |
Inc VAT. The fault-finding rate is agreed before we attend; repairs are priced in writing before parts are ordered.
Short winter days in Bridgend and what they mean
Bridgend sees roughly 7 hours 49 minutes of daylight in late December against 16 hours 38 minutes in June. Milder southern winters suit heat pumps well, though the system is still sized for a cold snap rather than an average day.
What happens when you book in Bridgend?
- Tell us the make if you know it, the error code or symptoms, and send photos of the unit and controller.
- We confirm the fault-finding rate and arrange a visit in Bridgend.
- The engineer diagnoses the fault and gives you a written price for the repair.
- Parts are ordered once you agree, and the repair is completed and tested.
Heat pump repairs in Bridgend: questions
How often should a heat pump in Bridgend be serviced?
Once a year is the usual recommendation, and many manufacturers make annual servicing a condition of the warranty. Check your warranty terms for the exact requirement.
Do you also cover Porthcawl?
Yes. We arrange heat pump servicing and repairs in Porthcawl, which is about 6 miles west of Bridgend, and across Mid Glamorgan.
Can you work on a heat pump in Bridgend that someone else installed?
Yes. We arrange servicing and repairs for most air source heat pumps in Bridgend, whoever fitted them. Tell us the make and model when you get in touch.
Why is my heat pump showing an error code?
An error code is the heat pump's way of reporting a problem it has detected, such as low water flow, a sensor reading out of range or a communication fault between units. Note the code and check the manual, as some codes clear after a simple reset or pressure top-up. If it returns, an engineer can trace the underlying cause.
Why does my heat pump keep switching on and off?
Frequent starting and stopping, called short cycling, is usually caused by an oversized heat pump, low water flow, too many zones closing at once or controls set with too narrow a range. It reduces efficiency and wears components. An engineer can check the settings, flow rates and design, and can often improve it with control changes before any parts are needed.