- Area
- Somerset
- Postcode district
- BS21
- Nation
- England
- Guide price
- From £90 inc VAT
- Visit
- Rate agreed in advance
Heat pump repairs in Clevedon: what to expect
Aftercare matters as much as installation. For a heat pump in Clevedon the visit checks the outdoor unit, the water circuit and the controls, and the engineer explains any settings that would help the system run more efficiently.
For repeated faults in Clevedon, the engineer looks at the system design as well as the failed part. We repair heat pumps in Clevedon whoever installed them, including older monobloc and split systems.
When a heat pump shows an error, loses pressure or stops heating, an engineer diagnoses the cause and explains the repair and its cost before fixing it.
- Rooms or hot water not getting warm enough
- Heat pumps installed by another company that need a second opinion
- Systems losing pressure or needing frequent topping up
What's included
- Fault-finding visit at a rate agreed before attending
- Refrigerant repairs by an F-gas certified engineer where needed
- A clear explanation of the fault and a price for the repair before work goes ahead
- Supply and fitting of replacement parts
- Testing of sensors, pumps, valves, pressures and electrics
Across Clevedon and Somerset, refrigerant repairs on split systems are carried out by an F-gas certified engineer.
Grants and rules for heat pumps in England
In England the Boiler Upgrade Scheme gives £7,500 towards an air source heat pump (£9,000 if it replaces oil or LPG, from 21 July 2026 to 31 March 2027), and since 28 April 2026 a valid EPC is no longer needed. The grant is applied for by the MCS-certified installer and shown as a deduction on your Clevedon quote.
What to budget for heat pump repairs in Clevedon
Guide prices for Somerset, including VAT. We agree the visit rate before anyone attends, so there are no surprises on the day.
| Repair | Guide price |
|---|---|
| Fault-finding visit and diagnosis | £90–£180 |
| Sensor or thermistor replacement | £120–£280 |
| Expansion vessel or pressure relief valve | £150–£350 |
| Circulating pump replacement | £250–£480 |
| Fan motor replacement | £300–£650 |
| Refrigerant leak repair and re-gas (split systems) | £350–£950 |
| Main control board (PCB) replacement | £450–£1,100 |
Inc VAT. The fault-finding rate is agreed before we attend; repairs are priced in writing before parts are ordered.
How long is the heating season in Clevedon?
On the shortest day Clevedon gets about 7 hours 50 minutes of daylight, and the winter sun reaches only around 15° above the horizon at noon. Winters this far south are milder than in most of the UK, which helps a heat pump run at low flow temperatures for much of the season.
Booking a visit in Clevedon
- Tell us the make if you know it, the error code or symptoms, and send photos of the unit and controller.
- We confirm the fault-finding rate and arrange a visit in Clevedon.
- The engineer diagnoses the fault and gives you a written price for the repair.
- Parts are ordered once you agree, and the repair is completed and tested.
Heat pump repairs in Clevedon: questions
Do you also cover Nailsea?
Yes. We arrange heat pump servicing and repairs in Nailsea, which is about 4 miles east of Clevedon, and across Somerset.
How often should a heat pump in Clevedon be serviced?
Once a year is the usual recommendation, and many manufacturers make annual servicing a condition of the warranty. Check your warranty terms for the exact requirement.
Will the engineer need access indoors as well as outside?
Usually yes. The outdoor unit, the hot water cylinder, the controls and the pipework and valves indoors are all part of the visit, so allow access to each.
Why is my heat pump showing an error code?
An error code is the heat pump's way of reporting a problem it has detected, such as low water flow, a sensor reading out of range or a communication fault between units. Note the code and check the manual, as some codes clear after a simple reset or pressure top-up. If it returns, an engineer can trace the underlying cause.
Do refrigerant repairs need a specialist?
Yes. Any work on a heat pump's refrigerant circuit, such as tracing a leak, replacing a component or re-gassing, must by law be done by an F-gas certified engineer where the refrigerant is fluorinated, such as R32; units using R290 (propane) need an engineer trained in flammable refrigerants. On split systems the refrigerant runs through pipes inside your home, so leaks there are more likely than on sealed monobloc units.