- Area
- Warwickshire
- Postcode district
- CV12
- Nation
- England
- Guide price
- From £90 inc VAT
- Visit
- Rate agreed in advance
What to know about heat pump repairs in Bedworth
A heat pump that is serviced and set up properly keeps running efficiently for many years. Many heat pump faults trace back to settings, low pressure or a worn part rather than the heat pump itself, and those can usually be put right.
Repairs in Bedworth that need a part ordered are explained and priced before the engineer leaves. Across Bedworth and Warwickshire, refrigerant repairs on split systems are carried out by an F-gas certified engineer.
When a heat pump shows an error, loses pressure or stops heating, an engineer diagnoses the cause and explains the repair and its cost before fixing it.
- Heat pumps installed by another company that need a second opinion
- Rooms or hot water not getting warm enough
- Systems losing pressure or needing frequent topping up
What's included
- System refill, venting and recommissioning after the repair
- A clear explanation of the fault and a price for the repair before work goes ahead
- Refrigerant repairs by an F-gas certified engineer where needed
- Fault-finding visit at a rate agreed before attending
- Reading of error history and operating data
For repeated faults in Bedworth, the engineer looks at the system design as well as the failed part.
Grants and rules for heat pumps in England
Homes in Bedworth can use the Boiler Upgrade Scheme, which takes £7,500 off the cost of an air source heat pump when it replaces fossil-fuel or electric heating. Replacing oil or LPG heating qualifies for £9,000 for installations from 21 July 2026 to 31 March 2027, and air-to-air systems for £2,500. The MCS-certified installer named in your quote applies for the grant and deducts it from the price.
Heat pump repairs costs around Bedworth
These are guide prices including VAT. The rate for your visit in Bedworth is confirmed before we book it, and any repair is priced in writing before parts are ordered.
| Repair | Guide price |
|---|---|
| Fault-finding visit and diagnosis | £90–£180 |
| Sensor or thermistor replacement | £120–£280 |
| Expansion vessel or pressure relief valve | £150–£350 |
| Circulating pump replacement | £250–£480 |
| Fan motor replacement | £300–£650 |
| Refrigerant leak repair and re-gas (split systems) | £350–£950 |
| Main control board (PCB) replacement | £450–£1,100 |
Inc VAT. The fault-finding rate is agreed before we attend; repairs are priced in writing before parts are ordered.
Designing for Bedworth's winters
Bedworth has about 7 hours 39 minutes of daylight at midwinter and 16 hours 50 minutes at midsummer. That swing matters if you pair a heat pump with solar panels: summer generation can cover much of the hot water, winter generation far less.
What happens when you book in Bedworth?
- Tell us the make if you know it, the error code or symptoms, and send photos of the unit and controller.
- We confirm the fault-finding rate and arrange a visit in Bedworth.
- The engineer diagnoses the fault and gives you a written price for the repair.
- Parts are ordered once you agree, and the repair is completed and tested.
Heat pump repairs in Bedworth: questions
Can you work on a heat pump in Bedworth that someone else installed?
Yes. We arrange servicing and repairs for most air source heat pumps in Bedworth, whoever fitted them. Tell us the make and model when you get in touch.
What should I check before booking a visit in Bedworth?
Note any error code on the controller, check the system pressure gauge if you have one, and make sure the outdoor unit is clear of leaves or snow. Photos of the unit and controller help.
Do you also cover Nuneaton?
Yes. We arrange heat pump servicing and repairs in Nuneaton, which is about 3 miles north of Bedworth, and across Warwickshire.
Why does my heat pump keep switching on and off?
Frequent starting and stopping, called short cycling, is usually caused by an oversized heat pump, low water flow, too many zones closing at once or controls set with too narrow a range. It reduces efficiency and wears components. An engineer can check the settings, flow rates and design, and can often improve it with control changes before any parts are needed.
Can you repair a heat pump installed by another company?
Yes. We carry out fault-finding and repairs on heat pumps installed by other companies, including monobloc and split systems. Tell us the make, model and approximate age when you get in touch, plus any error code shown. If the system is still under the manufacturer's warranty, it may be quicker to contact the original installer or manufacturer first.