- Area
- Warwickshire
- Postcode district
- CV9
- Nation
- England
- Guide price
- From £90 inc VAT
- Visit
- Rate agreed in advance
Heat pump repairs for Atherstone homes
A heat pump that is serviced and set up properly keeps running efficiently for many years. Many heat pump faults trace back to settings, low pressure or a worn part rather than the heat pump itself, and those can usually be put right.
Across Atherstone and Warwickshire, refrigerant repairs on split systems are carried out by an F-gas certified engineer. Repairs in Atherstone that need a part ordered are explained and priced before the engineer leaves.
When a heat pump shows an error, loses pressure or stops heating, an engineer diagnoses the cause and explains the repair and its cost before fixing it.
- Rooms or hot water not getting warm enough
- Outdoor units that have become noisy, iced up or keep switching on and off
- Systems losing pressure or needing frequent topping up
What's included
- Refrigerant repairs by an F-gas certified engineer where needed
- System refill, venting and recommissioning after the repair
- Reading of error history and operating data
- Testing of sensors, pumps, valves, pressures and electrics
- Supply and fitting of replacement parts
We repair heat pumps in Atherstone whoever installed them, including older monobloc and split systems.
Grants and rules for heat pumps in England
In England the Boiler Upgrade Scheme gives £7,500 towards an air source heat pump (£9,000 if it replaces oil or LPG, from 21 July 2026 to 31 March 2027), and since 28 April 2026 a valid EPC is no longer needed. The grant is applied for by the MCS-certified installer and shown as a deduction on your Atherstone quote.
Heat pump repairs prices in Atherstone
These are guide prices including VAT. The rate for your visit in Atherstone is confirmed before we book it, and any repair is priced in writing before parts are ordered.
| Repair | Guide price |
|---|---|
| Fault-finding visit and diagnosis | £90–£180 |
| Sensor or thermistor replacement | £120–£280 |
| Expansion vessel or pressure relief valve | £150–£350 |
| Circulating pump replacement | £250–£480 |
| Fan motor replacement | £300–£650 |
| Refrigerant leak repair and re-gas (split systems) | £350–£950 |
| Main control board (PCB) replacement | £450–£1,100 |
Inc VAT. The fault-finding rate is agreed before we attend; repairs are priced in writing before parts are ordered.
How long is the heating season in Atherstone?
On the shortest day Atherstone gets about 7 hours 38 minutes of daylight, with the noon sun around 14° up. The heating season runs from autumn into spring, so a heat pump that is sized correctly and set up with weather compensation does most of its work in steady, cool conditions.
How a visit works in Atherstone
- Tell us the make if you know it, the error code or symptoms, and send photos of the unit and controller.
- We confirm the fault-finding rate and arrange a visit in Atherstone.
- The engineer diagnoses the fault and gives you a written price for the repair.
- Parts are ordered once you agree, and the repair is completed and tested.
Heat pump repairs in Atherstone: questions
How often should a heat pump in Atherstone be serviced?
Once a year is the usual recommendation, and many manufacturers make annual servicing a condition of the warranty. Check your warranty terms for the exact requirement.
Can you work on a heat pump in Atherstone that someone else installed?
Yes. We arrange servicing and repairs for most air source heat pumps in Atherstone, whoever fitted them. Tell us the make and model when you get in touch.
What should I check before booking a visit in Atherstone?
Note any error code on the controller, check the system pressure gauge if you have one, and make sure the outdoor unit is clear of leaves or snow. Photos of the unit and controller help.
Why is my heat pump showing an error code?
An error code is the heat pump's way of reporting a problem it has detected, such as low water flow, a sensor reading out of range or a communication fault between units. Note the code and check the manual, as some codes clear after a simple reset or pressure top-up. If it returns, an engineer can trace the underlying cause.
Do refrigerant repairs need a specialist?
Yes. Any work on a heat pump's refrigerant circuit, such as tracing a leak, replacing a component or re-gassing, must by law be done by an F-gas certified engineer where the refrigerant is fluorinated, such as R32; units using R290 (propane) need an engineer trained in flammable refrigerants. On split systems the refrigerant runs through pipes inside your home, so leaks there are more likely than on sealed monobloc units.