- Area
- Greater Manchester
- Postcode district
- BL1
- Nation
- England
- Guide price
- From £120 inc VAT
- Visit
- Rate agreed in advance
Heat pump servicing for Bolton homes
A heat pump that is serviced and set up properly keeps running efficiently for many years. Many heat pump faults trace back to settings, low pressure or a worn part rather than the heat pump itself, and those can usually be put right.
We service heat pumps in Bolton whoever installed them, including monobloc and split systems. Heat pumps in Bolton that sit near trees or hedges often need their outdoor coil cleared of leaves at the annual service.
An annual service keeps a heat pump running efficiently, catches small faults early and is often a condition of the manufacturer's warranty.
- Heat pumps a year or more past installation
- Homes where running costs have crept up or rooms feel cooler than before
- Landlords who need dated service records for each property
What's included
- Expansion vessel, pressure relief and water quality checks
- Magnetic filter and strainer clean, with system pressure topped up
- Unvented cylinder safety checks and legionella cycle check
- Controls and error log check, with settings adjusted where needed
- Cleaning of the outdoor unit coil, fan area and condensate drain
Homes in Bolton and across Greater Manchester can book servicing at a time of year that suits them, ideally before winter.
Grants and rules for heat pumps in England
Homes in Bolton can use the Boiler Upgrade Scheme, which takes £7,500 off the cost of an air source heat pump when it replaces fossil-fuel or electric heating. Replacing oil or LPG heating qualifies for £9,000 for installations from 21 July 2026 to 31 March 2027, and air-to-air systems for £2,500. The MCS-certified installer named in your quote applies for the grant and deducts it from the price.
Guide prices for heat pump servicing in Bolton
These are guide prices including VAT. The rate for your visit in Bolton is confirmed before we book it, and any repair is priced in writing before parts are ordered.
| Visit | Guide price |
|---|---|
| Annual heat pump service | £120–£240 |
| Fault-finding visit (first hour) | £90–£180 |
Inc VAT. The rate for your visit is confirmed before booking.
Designing for Bolton's winters
Bolton sees roughly 7 hours 27 minutes of daylight in December and 17 hours 03 minutes in June. With a longer heating season than the south, the gains from low flow temperatures and good controls add up over the year.
What happens when you book in Bolton?
- Book a service and tell us roughly how old the system is.
- An engineer visits your Bolton home and works through the service checklist.
- You receive a written record of the service and any recommendations.
- If a repair is needed, it is priced in writing before any work goes ahead.
Heat pump servicing in Bolton: questions
What should I check before booking a visit in Bolton?
Note any error code on the controller, check the system pressure gauge if you have one, and make sure the outdoor unit is clear of leaves or snow. Photos of the unit and controller help.
How much does a visit cost in Bolton?
The rate for a service or fault-finding visit is agreed before anyone attends. Any repair is priced in writing before parts are ordered, so you decide before work goes ahead.
Do you also cover Radcliffe?
Yes. We arrange heat pump servicing and repairs in Radcliffe, which is about 5 miles east of Bolton, and across Greater Manchester.
How often should a heat pump be serviced?
Once a year is the usual recommendation for air source heat pumps, and many manufacturers require it as a warranty condition. An annual visit cleans filters and strainers, checks pressures and controls, and tests the unvented cylinder's safety devices. If you notice a drop in performance, unusual noises or repeated error codes between services, arrange a visit sooner.
Can you service a split system?
Yes. Split systems have refrigerant pipes running between the outdoor unit and an indoor unit, and checks on that refrigerant circuit must be done by an F-gas certified engineer. We arrange the service so a suitably certified engineer attends. The water side, controls and cylinder are checked in the same visit, just as on a monobloc system.