- Area
- West Midlands
- Postcode district
- WS9
- Nation
- England
- Guide price
- From £120 inc VAT
- Visit
- Rate agreed in advance
Before you book: heat pump servicing in Aldridge
A heat pump that is serviced and set up properly keeps running efficiently for many years. Many heat pump faults trace back to settings, low pressure or a worn part rather than the heat pump itself, and those can usually be put right.
Homes in Aldridge and across the West Midlands can book servicing at a time of year that suits them, ideally before winter. Service visits in Aldridge include unvented cylinder safety checks alongside the heat pump itself.
An annual service keeps a heat pump running efficiently, catches small faults early and is often a condition of the manufacturer's warranty.
- Heat pumps a year or more past installation
- Landlords who need dated service records for each property
- Systems where the manufacturer's warranty requires annual servicing
What's included
- Expansion vessel, pressure relief and water quality checks
- Magnetic filter and strainer clean, with system pressure topped up
- Cleaning of the outdoor unit coil, fan area and condensate drain
- A dated service record for your warranty and property files
- Unvented cylinder safety checks and legionella cycle check
Heat pumps in Aldridge that sit near trees or hedges often need their outdoor coil cleared of leaves at the annual service.
Grants and rules for heat pumps in England
In England the Boiler Upgrade Scheme gives £7,500 towards an air source heat pump (£9,000 if it replaces oil or LPG, from 21 July 2026 to 31 March 2027), and since 28 April 2026 a valid EPC is no longer needed. The grant is applied for by the MCS-certified installer and shown as a deduction on your Aldridge quote.
Heat pump servicing costs around Aldridge
These are guide prices including VAT. The rate for your visit in Aldridge is confirmed before we book it, and any repair is priced in writing before parts are ordered.
| Visit | Guide price |
|---|---|
| Annual heat pump service | £120–£250 |
| Fault-finding visit (first hour) | £90–£180 |
Inc VAT. The rate for your visit is confirmed before booking.
Designing for Aldridge's winters
On the shortest day Aldridge gets about 7 hours 38 minutes of daylight, with the noon sun around 14° up. The heating season runs from autumn into spring, so a heat pump that is sized correctly and set up with weather compensation does most of its work in steady, cool conditions.
How a visit works in Aldridge
- Book a service and tell us roughly how old the system is.
- An engineer visits your Aldridge home and works through the service checklist.
- You receive a written record of the service and any recommendations.
- If a repair is needed, it is priced in writing before any work goes ahead.
Heat pump servicing in Aldridge: questions
What should I check before booking a visit in Aldridge?
Note any error code on the controller, check the system pressure gauge if you have one, and make sure the outdoor unit is clear of leaves or snow. Photos of the unit and controller help.
Can you work on a heat pump in Aldridge that someone else installed?
Yes. We arrange servicing and repairs for most air source heat pumps in Aldridge, whoever fitted them. Tell us the make and model when you get in touch.
How often should a heat pump in Aldridge be serviced?
Once a year is the usual recommendation, and many manufacturers make annual servicing a condition of the warranty. Check your warranty terms for the exact requirement.
Can you service a split system?
Yes. Split systems have refrigerant pipes running between the outdoor unit and an indoor unit, and checks on that refrigerant circuit must be done by an F-gas certified engineer. We arrange the service so a suitably certified engineer attends. The water side, controls and cylinder are checked in the same visit, just as on a monobloc system.
How often should a heat pump be serviced?
Once a year is the usual recommendation for air source heat pumps, and many manufacturers require it as a warranty condition. An annual visit cleans filters and strainers, checks pressures and controls, and tests the unvented cylinder's safety devices. If you notice a drop in performance, unusual noises or repeated error codes between services, arrange a visit sooner.