A heat pump hot water cylinder is an insulated tank that stores hot water heated by the heat pump, with a much larger internal coil than a cylinder designed for a boiler. Heat pumps heat water to a lower temperature than boilers, typically around 45–55°C, so a bigger coil is needed to pass heat into the stored water quickly. A standard boiler cylinder would heat slowly and make the heat pump work harder than it should.
Discharge pipe routes are planned at the survey so a Bedfordshire cylinder can drain safely to the outside. Cylinder sizes for Bedfordshire homes are based on the people living there and the bathrooms in daily use. Many homes in Bedfordshire with combi boilers have no airing cupboard, so the survey looks for the most practical cylinder space.
Who it suits
- Homes with solar PV that want to store daytime electricity as hot water
- Larger families or homes with two or more bathrooms
- Homes replacing a combi boiler that need space found for a cylinder
- Every air-to-water heat pump installation, whatever the existing boiler
Grants and rules for heat pumps in England
In England the Boiler Upgrade Scheme gives £7,500 towards an air source heat pump (£9,000 if it replaces oil or LPG, from 21 July 2026 to 31 March 2027), and since 28 April 2026 a valid EPC is no longer needed. The grant is applied for by the MCS-certified installer and shown as a deduction on your quote.
Installing heat pumps is zero-rated for VAT across the UK until 31 March 2027. Since 29 May 2025, permitted development in England allows up to two air source heat pumps on a house, each up to 1.5 m³, with no blanket 1 m boundary rule — the installation must still meet the MCS planning standards, including the noise check. Listed buildings, flats and some conservation-area positions need extra consent, which we check at survey.
Heat pump hot water cylinders prices in Bedfordshire
Here are typical prices for heat pump hot water cylinders in Bedfordshire, installed and including VAT. Use the guide price tool for a figure based on your home, then a survey confirms it in writing.
| Work | Guide price |
|---|---|
| Heat pump hot water cylinder (supplied and fitted) | £1,200–£2,250 |
Supplied and fitted, inc VAT. Included in every full system price.
Towns we cover in Bedfordshire
We cover 9 towns in Bedfordshire for heat pump hot water cylinders. Each links to local guide prices and the grant position for England.
| Town | Postcode district | Nearest town | Midwinter daylight |
|---|---|---|---|
| Luton | LU1 | Dunstable | 7 h 46 min |
| Bedford | MK40 | Kempston | 7 h 43 min |
| Dunstable | LU6 | Luton | 7 h 46 min |
| Leighton Buzzard | LU7 | Dunstable | 7 h 45 min |
| Ampthill | MK45 | Flitwick | 7 h 44 min |
| Kempston | MK42 | Bedford | 7 h 43 min |
| Biggleswade | SG18 | Sandy | 7 h 43 min |
| Flitwick | MK45 | Ampthill | 7 h 44 min |
| Sandy | SG19 | Biggleswade | 7 h 43 min |
Heat pump hot water cylinders questions
Do I need good water pressure for an unvented cylinder?
Yes. An unvented cylinder runs at mains pressure, so it needs enough incoming pressure and flow to supply your taps and showers well. We measure your mains supply at the survey. If flow is low, options include a different cylinder type or an upgrade to the incoming supply pipe, which we explain before you commit.
Can I keep my existing hot water cylinder with a heat pump?
Usually not. Cylinders designed for boilers have a small coil that cannot transfer heat quickly at heat pump temperatures, so the water would reheat slowly and efficiency would suffer. A heat pump cylinder has a much larger coil. The new cylinder can often go in the same cupboard, though, if there is enough height and floor space.
Does a heat pump cylinder need servicing?
Yes. An unvented cylinder's safety devices should be checked every year, including the relief valves, the expansion vessel charge and the discharge pipework. This is normally done as part of the annual heat pump service, and it is often a condition of the cylinder manufacturer's warranty. Keep the cylinder paperwork with your heat pump handover documents.
How much does a heat pump cylinder cost?
A heat pump hot water cylinder has a guide price of £1,200–£2,200, installed and including VAT. In a full heat pump installation the cylinder is already included in the system guide price, so this figure mainly applies where a cylinder is replaced on its own. Capacity, coil design and the pipework needed affect where your price sits.