Heat pump repair is the diagnosis and fixing of faults in an air source heat pump, its water circuit, its controls or the hot water cylinder. Many faults have a simple cause, such as low system pressure, a blocked filter or a control setting, while others involve a failed sensor, pump, fan or circuit board.
We repair heat pumps in County Londonderry whoever installed them, including older monobloc and split systems. Repairs in County Londonderry that need a part ordered are explained and priced before the engineer leaves. Outdoor units in exposed spots around County Londonderry can ice more heavily, so siting is checked as part of any icing fault.
Who it suits
- Rooms or hot water not getting warm enough
- Systems losing pressure or needing frequent topping up
- Outdoor units that have become noisy, iced up or keep switching on and off
- Heat pumps installed by another company that need a second opinion
Grants and rules for heat pumps in Northern Ireland
The Boiler Upgrade Scheme covers England and Wales only, and there is currently no dedicated heat pump grant for homeowners in Northern Ireland. Our quote for a home in County Londonderry is therefore shown without a grant deduction; if support becomes available we will tell you how it applies.
Heat pump repairs prices in County Londonderry
Guide prices for County Londonderry, including VAT. We agree the visit rate before anyone attends, so there are no surprises on the day.
| Repair | Guide price |
|---|---|
| Fault-finding visit and diagnosis | £90–£170 |
| Sensor or thermistor replacement | £120–£270 |
| Expansion vessel or pressure relief valve | £150–£340 |
| Circulating pump replacement | £240–£470 |
| Fan motor replacement | £290–£630 |
| Refrigerant leak repair and re-gas (split systems) | £340–£920 |
| Main control board (PCB) replacement | £440–£1,050 |
Inc VAT. The fault-finding rate is agreed before we attend; repairs are priced in writing before parts are ordered.
Towns we cover in County Londonderry
We cover 7 towns in County Londonderry for heat pump repairs. Each links to local guide prices and the grant position for Northern Ireland.
| Town | Postcode district | Nearest town | Midwinter daylight |
|---|---|---|---|
| Derry/Londonderry | BT48 | Limavady | 7 h 10 min |
| Coleraine | BT52 | Portstewart | 7 h 08 min |
| Dungiven | BT47 | Limavady | 7 h 11 min |
| Limavady | BT49 | Dungiven | 7 h 09 min |
| Maghera | BT46 | Magherafelt | 7 h 12 min |
| Magherafelt | BT45 | Maghera | 7 h 13 min |
| Portstewart | BT55 | Coleraine | 7 h 08 min |
Heat pump repairs questions
Do refrigerant repairs need a specialist?
Yes. Any work on a heat pump's refrigerant circuit, such as tracing a leak, replacing a component or re-gassing, must by law be done by an F-gas certified engineer where the refrigerant is fluorinated, such as R32; units using R290 (propane) need an engineer trained in flammable refrigerants. On split systems the refrigerant runs through pipes inside your home, so leaks there are more likely than on sealed monobloc units.
Can you repair a heat pump installed by another company?
Yes. We carry out fault-finding and repairs on heat pumps installed by other companies, including monobloc and split systems. Tell us the make, model and approximate age when you get in touch, plus any error code shown. If the system is still under the manufacturer's warranty, it may be quicker to contact the original installer or manufacturer first.
Why is my heat pump showing an error code?
An error code is the heat pump's way of reporting a problem it has detected, such as low water flow, a sensor reading out of range or a communication fault between units. Note the code and check the manual, as some codes clear after a simple reset or pressure top-up. If it returns, an engineer can trace the underlying cause.
Why does my heat pump keep switching on and off?
Frequent starting and stopping, called short cycling, is usually caused by an oversized heat pump, low water flow, too many zones closing at once or controls set with too narrow a range. It reduces efficiency and wears components. An engineer can check the settings, flow rates and design, and can often improve it with control changes before any parts are needed.