- Area
- East Sussex
- Postcode district
- TN31
- Nation
- England
- Guide price
- From £90 inc VAT
- Visit
- Rate agreed in advance
Heat pump repairs for Rye homes
A heat pump that is serviced and set up properly keeps running efficiently for many years. Many heat pump faults trace back to settings, low pressure or a worn part rather than the heat pump itself, and those can usually be put right.
Across Rye and East Sussex, refrigerant repairs on split systems are carried out by an F-gas certified engineer. Repairs in Rye that need a part ordered are explained and priced before the engineer leaves.
When a heat pump shows an error, loses pressure or stops heating, an engineer diagnoses the cause and explains the repair and its cost before fixing it.
- Outdoor units that have become noisy, iced up or keep switching on and off
- Systems losing pressure or needing frequent topping up
- Rooms or hot water not getting warm enough
What's included
- Supply and fitting of replacement parts
- Reading of error history and operating data
- A clear explanation of the fault and a price for the repair before work goes ahead
- System refill, venting and recommissioning after the repair
- Fault-finding visit at a rate agreed before attending
We repair heat pumps in Rye whoever installed them, including older monobloc and split systems.
Grants and rules for heat pumps in England
Homes in Rye can use the Boiler Upgrade Scheme, which takes £7,500 off the cost of an air source heat pump when it replaces fossil-fuel or electric heating. Replacing oil or LPG heating qualifies for £9,000 for installations from 21 July 2026 to 31 March 2027, and air-to-air systems for £2,500. The MCS-certified installer named in your quote applies for the grant and deducts it from the price.
Heat pump repairs prices in Rye
These are guide prices including VAT. The rate for your visit in Rye is confirmed before we book it, and any repair is priced in writing before parts are ordered.
| Repair | Guide price |
|---|---|
| Fault-finding visit and diagnosis | £90–£190 |
| Sensor or thermistor replacement | £120–£290 |
| Expansion vessel or pressure relief valve | £150–£360 |
| Circulating pump replacement | £260–£490 |
| Fan motor replacement | £310–£670 |
| Refrigerant leak repair and re-gas (split systems) | £360–£980 |
| Main control board (PCB) replacement | £460–£1,150 |
Inc VAT. The fault-finding rate is agreed before we attend; repairs are priced in writing before parts are ordered.
Winter daylight and heating in Rye
Rye sees roughly 7 hours 55 minutes of daylight in late December against 16 hours 32 minutes in June. Milder southern winters suit heat pumps well, though the system is still sized for a cold snap rather than an average day.
How a visit works in Rye
- Tell us the make if you know it, the error code or symptoms, and send photos of the unit and controller.
- We confirm the fault-finding rate and arrange a visit in Rye.
- The engineer diagnoses the fault and gives you a written price for the repair.
- Parts are ordered once you agree, and the repair is completed and tested.
Heat pump repairs in Rye: questions
Do you also cover Hastings?
Yes. We arrange heat pump servicing and repairs in Hastings, which is about 9 miles south-west of Rye, and across East Sussex.
Can you work on a heat pump in Rye that someone else installed?
Yes. We arrange servicing and repairs for most air source heat pumps in Rye, whoever fitted them. Tell us the make and model when you get in touch.
How much does a visit cost in Rye?
The rate for a service or fault-finding visit is agreed before anyone attends. Any repair is priced in writing before parts are ordered, so you decide before work goes ahead.
Can you repair a heat pump installed by another company?
Yes. We carry out fault-finding and repairs on heat pumps installed by other companies, including monobloc and split systems. Tell us the make, model and approximate age when you get in touch, plus any error code shown. If the system is still under the manufacturer's warranty, it may be quicker to contact the original installer or manufacturer first.
Why is my heat pump showing an error code?
An error code is the heat pump's way of reporting a problem it has detected, such as low water flow, a sensor reading out of range or a communication fault between units. Note the code and check the manual, as some codes clear after a simple reset or pressure top-up. If it returns, an engineer can trace the underlying cause.