- Area
- Hampshire
- Postcode district
- GU46
- Nation
- England
- Guide price
- From £90 inc VAT
- Visit
- Rate agreed in advance
Before you book: heat pump repairs in Yateley
A heat pump that is serviced and set up properly keeps running efficiently for many years. Many heat pump faults trace back to settings, low pressure or a worn part rather than the heat pump itself, and those can usually be put right.
Repairs in Yateley that need a part ordered are explained and priced before the engineer leaves. For repeated faults in Yateley, the engineer looks at the system design as well as the failed part.
When a heat pump shows an error, loses pressure or stops heating, an engineer diagnoses the cause and explains the repair and its cost before fixing it.
- Outdoor units that have become noisy, iced up or keep switching on and off
- Rooms or hot water not getting warm enough
- Systems losing pressure or needing frequent topping up
What's included
- Fault-finding visit at a rate agreed before attending
- A clear explanation of the fault and a price for the repair before work goes ahead
- System refill, venting and recommissioning after the repair
- Refrigerant repairs by an F-gas certified engineer where needed
- Supply and fitting of replacement parts
We repair heat pumps in Yateley whoever installed them, including older monobloc and split systems.
Grants and rules for heat pumps in England
Homes in Yateley can use the Boiler Upgrade Scheme, which takes £7,500 off the cost of an air source heat pump when it replaces fossil-fuel or electric heating. Replacing oil or LPG heating qualifies for £9,000 for installations from 21 July 2026 to 31 March 2027, and air-to-air systems for £2,500. The MCS-certified installer named in your quote applies for the grant and deducts it from the price.
Heat pump repairs prices in Yateley
These are guide prices including VAT. The rate for your visit in Yateley is confirmed before we book it, and any repair is priced in writing before parts are ordered.
| Repair | Guide price |
|---|---|
| Fault-finding visit and diagnosis | £90–£190 |
| Sensor or thermistor replacement | £120–£290 |
| Expansion vessel or pressure relief valve | £150–£360 |
| Circulating pump replacement | £260–£490 |
| Fan motor replacement | £310–£670 |
| Refrigerant leak repair and re-gas (split systems) | £360–£980 |
| Main control board (PCB) replacement | £460–£1,150 |
Inc VAT. The fault-finding rate is agreed before we attend; repairs are priced in writing before parts are ordered.
Short winter days in Yateley and what they mean
On the shortest day Yateley gets about 7 hours 51 minutes of daylight, and the winter sun reaches only around 15° above the horizon at noon. Winters this far south are milder than in most of the UK, which helps a heat pump run at low flow temperatures for much of the season.
What happens when you book in Yateley?
- Tell us the make if you know it, the error code or symptoms, and send photos of the unit and controller.
- We confirm the fault-finding rate and arrange a visit in Yateley.
- The engineer diagnoses the fault and gives you a written price for the repair.
- Parts are ordered once you agree, and the repair is completed and tested.
Heat pump repairs in Yateley: questions
Do you also cover Fleet?
Yes. We arrange heat pump servicing and repairs in Fleet, which is about 4 miles south of Yateley, and across Hampshire.
How much does a visit cost in Yateley?
The rate for a service or fault-finding visit is agreed before anyone attends. Any repair is priced in writing before parts are ordered, so you decide before work goes ahead.
How often should a heat pump in Yateley be serviced?
Once a year is the usual recommendation, and many manufacturers make annual servicing a condition of the warranty. Check your warranty terms for the exact requirement.
Why does my heat pump keep switching on and off?
Frequent starting and stopping, called short cycling, is usually caused by an oversized heat pump, low water flow, too many zones closing at once or controls set with too narrow a range. It reduces efficiency and wears components. An engineer can check the settings, flow rates and design, and can often improve it with control changes before any parts are needed.
Why is my heat pump showing an error code?
An error code is the heat pump's way of reporting a problem it has detected, such as low water flow, a sensor reading out of range or a communication fault between units. Note the code and check the manual, as some codes clear after a simple reset or pressure top-up. If it returns, an engineer can trace the underlying cause.