- Area
- West Yorkshire
- Postcode district
- BD1
- Nation
- England
- Guide price
- From £90 inc VAT
- Visit
- Rate agreed in advance
Heat pump repairs in Bradford: what to expect
Whoever installed your heat pump, aftercare can be arranged in Bradford. Tell us the make and model and roughly how old it is, and we will set out what the visit involves before you book.
Repairs in Bradford that need a part ordered are explained and priced before the engineer leaves. Outdoor units in exposed spots around Bradford can ice more heavily, so siting is checked as part of any icing fault.
When a heat pump shows an error, loses pressure or stops heating, an engineer diagnoses the cause and explains the repair and its cost before fixing it.
- Heat pumps showing an error code or fault light
- Outdoor units that have become noisy, iced up or keep switching on and off
- Rooms or hot water not getting warm enough
What's included
- Testing of sensors, pumps, valves, pressures and electrics
- Supply and fitting of replacement parts
- Fault-finding visit at a rate agreed before attending
- Reading of error history and operating data
- System refill, venting and recommissioning after the repair
Across Bradford and West Yorkshire, refrigerant repairs on split systems are carried out by an F-gas certified engineer.
Grants and rules for heat pumps in England
Homes in Bradford can use the Boiler Upgrade Scheme, which takes £7,500 off the cost of an air source heat pump when it replaces fossil-fuel or electric heating. Replacing oil or LPG heating qualifies for £9,000 for installations from 21 July 2026 to 31 March 2027, and air-to-air systems for £2,500. The MCS-certified installer named in your quote applies for the grant and deducts it from the price.
Heat pump repairs prices in Bradford
Guide prices for West Yorkshire, including VAT. We agree the visit rate before anyone attends, so there are no surprises on the day.
| Repair | Guide price |
|---|---|
| Fault-finding visit and diagnosis | £90–£180 |
| Sensor or thermistor replacement | £120–£270 |
| Expansion vessel or pressure relief valve | £150–£340 |
| Circulating pump replacement | £240–£470 |
| Fan motor replacement | £290–£640 |
| Refrigerant leak repair and re-gas (split systems) | £340–£930 |
| Main control board (PCB) replacement | £440–£1,100 |
Inc VAT. The fault-finding rate is agreed before we attend; repairs are priced in writing before parts are ordered.
Winter daylight and heating in Bradford
Bradford sees roughly 7 hours 25 minutes of daylight in December and 17 hours 06 minutes in June. With a longer heating season than the south, the gains from low flow temperatures and good controls add up over the year.
How a visit works in Bradford
- Tell us the make if you know it, the error code or symptoms, and send photos of the unit and controller.
- We confirm the fault-finding rate and arrange a visit in Bradford.
- The engineer diagnoses the fault and gives you a written price for the repair.
- Parts are ordered once you agree, and the repair is completed and tested.
Heat pump repairs in Bradford: questions
Can you work on a heat pump in Bradford that someone else installed?
Yes. We arrange servicing and repairs for most air source heat pumps in Bradford, whoever fitted them. Tell us the make and model when you get in touch.
How much does a visit cost in Bradford?
The rate for a service or fault-finding visit is agreed before anyone attends. Any repair is priced in writing before parts are ordered, so you decide before work goes ahead.
Will the engineer need access indoors as well as outside?
Usually yes. The outdoor unit, the hot water cylinder, the controls and the pipework and valves indoors are all part of the visit, so allow access to each.
How much does a heat pump repair cost?
Heat pump repairs have a typical range of £90–£1,100, including VAT, depending on the part and labour involved. Sensor replacements sit at the lower end, while control boards and refrigerant repairs on split systems sit higher. Every repair starts with a fault-finding visit, with a guide price of £90–£180 for the first hour, and the repair is priced before work goes ahead.
Why is my heat pump showing an error code?
An error code is the heat pump's way of reporting a problem it has detected, such as low water flow, a sensor reading out of range or a communication fault between units. Note the code and check the manual, as some codes clear after a simple reset or pressure top-up. If it returns, an engineer can trace the underlying cause.