- Area
- Kent
- Postcode district
- ME2
- Nation
- England
- Guide price
- From £90 inc VAT
- Visit
- Rate agreed in advance
Heat pump repairs in Strood: what to expect
Whoever installed your heat pump, aftercare can be arranged in Strood. Tell us the make and model and roughly how old it is, and we will set out what the visit involves before you book.
Heat pump owners in Strood can arrange a fault-finding visit at a rate agreed before an engineer attends. Across Strood and Kent, refrigerant repairs on split systems are carried out by an F-gas certified engineer.
When a heat pump shows an error, loses pressure or stops heating, an engineer diagnoses the cause and explains the repair and its cost before fixing it.
- Outdoor units that have become noisy, iced up or keep switching on and off
- Systems losing pressure or needing frequent topping up
- Heat pumps showing an error code or fault light
What's included
- System refill, venting and recommissioning after the repair
- Refrigerant repairs by an F-gas certified engineer where needed
- A clear explanation of the fault and a price for the repair before work goes ahead
- Fault-finding visit at a rate agreed before attending
- Supply and fitting of replacement parts
For repeated faults in Strood, the engineer looks at the system design as well as the failed part.
Grants and rules for heat pumps in England
Homes in Strood can use the Boiler Upgrade Scheme, which takes £7,500 off the cost of an air source heat pump when it replaces fossil-fuel or electric heating. Replacing oil or LPG heating qualifies for £9,000 for installations from 21 July 2026 to 31 March 2027, and air-to-air systems for £2,500. The MCS-certified installer named in your quote applies for the grant and deducts it from the price.
Heat pump repairs prices in Strood
These are guide prices including VAT. The rate for your visit in Strood is confirmed before we book it, and any repair is priced in writing before parts are ordered.
| Repair | Guide price |
|---|---|
| Fault-finding visit and diagnosis | £90–£190 |
| Sensor or thermistor replacement | £120–£290 |
| Expansion vessel or pressure relief valve | £150–£360 |
| Circulating pump replacement | £260–£490 |
| Fan motor replacement | £310–£670 |
| Refrigerant leak repair and re-gas (split systems) | £360–£980 |
| Main control board (PCB) replacement | £460–£1,150 |
Inc VAT. The fault-finding rate is agreed before we attend; repairs are priced in writing before parts are ordered.
Winter daylight and heating in Strood
On the shortest day Strood gets about 7 hours 51 minutes of daylight, and the winter sun reaches only around 15° above the horizon at noon. Winters this far south are milder than in most of the UK, which helps a heat pump run at low flow temperatures for much of the season.
Booking a visit in Strood
- Tell us the make if you know it, the error code or symptoms, and send photos of the unit and controller.
- We confirm the fault-finding rate and arrange a visit in Strood.
- The engineer diagnoses the fault and gives you a written price for the repair.
- Parts are ordered once you agree, and the repair is completed and tested.
Heat pump repairs in Strood: questions
How often should a heat pump in Strood be serviced?
Once a year is the usual recommendation, and many manufacturers make annual servicing a condition of the warranty. Check your warranty terms for the exact requirement.
How much does a visit cost in Strood?
The rate for a service or fault-finding visit is agreed before anyone attends. Any repair is priced in writing before parts are ordered, so you decide before work goes ahead.
Do you also cover Rochester?
Yes. We arrange heat pump servicing and repairs in Rochester, which is about a mile east of Strood, and across Kent.
Is ice on my heat pump a fault?
Some frost on the outdoor unit in cold, damp weather is normal, and the unit clears it with regular defrost cycles, often releasing a little vapour. It becomes a fault when thick ice builds up and does not clear, or when ice blocks the fan. That can point to poor airflow, a failed sensor, drainage problems or low refrigerant, and needs checking.
Why is my heat pump showing an error code?
An error code is the heat pump's way of reporting a problem it has detected, such as low water flow, a sensor reading out of range or a communication fault between units. Note the code and check the manual, as some codes clear after a simple reset or pressure top-up. If it returns, an engineer can trace the underlying cause.