Most heat pump cylinders are unvented, meaning they run at mains water pressure and give strong flow from every tap without a cold water tank in the loft. Unvented cylinders have safety controls that must be fitted and checked by someone qualified to work on them. We size the cylinder from your household and bathrooms, confirm your mains water supply can support it, and plan the space, pipework and discharge route at the survey.
Many homes in West Glamorgan with combi boilers have no airing cupboard, so the survey looks for the most practical cylinder space. Older houses in West Glamorgan with loft tanks can usually have them removed when an unvented cylinder is fitted. We check mains water pressure and flow at each West Glamorgan property before choosing a cylinder.
Who it suits
- Homes with solar PV that want to store daytime electricity as hot water
- Homes replacing a combi boiler that need space found for a cylinder
- Every air-to-water heat pump installation, whatever the existing boiler
- Larger families or homes with two or more bathrooms
Grants and rules for heat pumps in Wales
In Wales the Boiler Upgrade Scheme gives £7,500 towards an air source heat pump (£9,000 if it replaces oil or LPG, from 21 July 2026 to 31 March 2027; £2,500 for air-to-air). The MCS-certified installer named in your quote applies to Ofgem for you, and the grant comes off your quote.
There is no VAT on installing a heat pump anywhere in the UK, Wales included, until 31 March 2027. Planning rules for heat pumps in Wales are set by the Welsh Government and differ from England's, so the surveyor checks the unit position against them.
Heat pump hot water cylinders prices in West Glamorgan
These are guide prices for West Glamorgan, installed and including VAT. Your final price is fixed in a written quote after the survey and depends on the heat loss of the house, the radiators that need changing and where the unit goes.
| Work | Guide price |
|---|---|
| Heat pump hot water cylinder (supplied and fitted) | £1,200–£2,200 |
Supplied and fitted, inc VAT. Included in every full system price.
Towns we cover in West Glamorgan
We cover 8 towns in West Glamorgan for heat pump hot water cylinders. Each links to local guide prices and the grant position for Wales.
| Town | Postcode district | Nearest town | Midwinter daylight |
|---|---|---|---|
| Swansea | SA1 | Mumbles | 7 h 48 min |
| Neath | SA10 | Briton Ferry | 7 h 48 min |
| Briton Ferry | SA12 | Neath | 7 h 48 min |
| Gorseinon | SA4 | Swansea | 7 h 48 min |
| Clydach | SA6 | Pontardawe | 7 h 48 min |
| Mumbles | SA3 | Swansea | 7 h 49 min |
| Pontardawe | SA8 | Clydach | 7 h 47 min |
| Port Talbot | SA12 | Briton Ferry | 7 h 49 min |
Heat pump hot water cylinders questions
Can I keep my existing hot water cylinder with a heat pump?
Usually not. Cylinders designed for boilers have a small coil that cannot transfer heat quickly at heat pump temperatures, so the water would reheat slowly and efficiency would suffer. A heat pump cylinder has a much larger coil. The new cylinder can often go in the same cupboard, though, if there is enough height and floor space.
How much does a heat pump cylinder cost?
A heat pump hot water cylinder has a guide price of £1,200–£2,200, installed and including VAT. In a full heat pump installation the cylinder is already included in the system guide price, so this figure mainly applies where a cylinder is replaced on its own. Capacity, coil design and the pipework needed affect where your price sits.
I have a combi boiler. Where will the cylinder go?
Moving from a combi to a heat pump means finding space for a cylinder, usually somewhere around 600 mm square and up to about 2 m tall. Common choices are a bedroom or landing cupboard, a utility room, under the stairs or an integral garage. The surveyor looks at your layout and suggests options, including slimline models where space is tight.
Do I need good water pressure for an unvented cylinder?
Yes. An unvented cylinder runs at mains pressure, so it needs enough incoming pressure and flow to supply your taps and showers well. We measure your mains supply at the survey. If flow is low, options include a different cylinder type or an upgrade to the incoming supply pipe, which we explain before you commit.