- Area
- Perth and Kinross
- Postcode district
- PH15
- Nation
- Scotland
- Guide price
- From £90 inc VAT
- Visit
- Rate agreed in advance
Before you book: heat pump repairs in Aberfeldy
Whoever installed your heat pump, aftercare can be arranged in Aberfeldy. Tell us the make and model and roughly how old it is, and we will set out what the visit involves before you book.
We repair heat pumps in Aberfeldy whoever installed them, including older monobloc and split systems. For repeated faults in Aberfeldy, the engineer looks at the system design as well as the failed part.
When a heat pump shows an error, loses pressure or stops heating, an engineer diagnoses the cause and explains the repair and its cost before fixing it.
- Heat pumps installed by another company that need a second opinion
- Heat pumps showing an error code or fault light
- Systems losing pressure or needing frequent topping up
What's included
- Fault-finding visit at a rate agreed before attending
- Supply and fitting of replacement parts
- Refrigerant repairs by an F-gas certified engineer where needed
- System refill, venting and recommissioning after the repair
- Testing of sensors, pumps, valves, pressures and electrics
Outdoor units in exposed spots around Aberfeldy can ice more heavily, so siting is checked as part of any icing fault.
Grants and rules for heat pumps in Scotland
The Boiler Upgrade Scheme does not apply in Scotland. Instead, homeowners in Aberfeldy can apply to Home Energy Scotland for a grant of up to £7,500 towards a heat pump, with up to £1,500 more for eligible rural and island homes, plus an optional interest-free loan of up to £7,500. You need a written funding offer before any work starts.
Guide prices for heat pump repairs in Aberfeldy
These are guide prices including VAT. The rate for your visit in Aberfeldy is confirmed before we book it, and any repair is priced in writing before parts are ordered.
| Repair | Guide price |
|---|---|
| Fault-finding visit and diagnosis | £90–£180 |
| Sensor or thermistor replacement | £120–£280 |
| Expansion vessel or pressure relief valve | £150–£350 |
| Circulating pump replacement | £250–£480 |
| Fan motor replacement | £300–£660 |
| Refrigerant leak repair and re-gas (split systems) | £350–£960 |
| Main control board (PCB) replacement | £450–£1,100 |
Inc VAT. The fault-finding rate is agreed before we attend; repairs are priced in writing before parts are ordered.
Designing for Aberfeldy's winters
On the shortest day Aberfeldy gets only about 6 hours 48 minutes of daylight, with the sun around 10° up at noon. Long Scottish winters mean the heat pump runs for much of the year, so careful sizing, good controls and correctly sized radiators make a real difference.
Booking a visit in Aberfeldy
- Tell us the make if you know it, the error code or symptoms, and send photos of the unit and controller.
- We confirm the fault-finding rate and arrange a visit in Aberfeldy.
- The engineer diagnoses the fault and gives you a written price for the repair.
- Parts are ordered once you agree, and the repair is completed and tested.
Heat pump repairs in Aberfeldy: questions
Can you work on a heat pump in Aberfeldy that someone else installed?
Yes. We arrange servicing and repairs for most air source heat pumps in Aberfeldy, whoever fitted them. Tell us the make and model when you get in touch.
Will the engineer need access indoors as well as outside?
Usually yes. The outdoor unit, the hot water cylinder, the controls and the pipework and valves indoors are all part of the visit, so allow access to each.
How often should a heat pump in Aberfeldy be serviced?
Once a year is the usual recommendation, and many manufacturers make annual servicing a condition of the warranty. Check your warranty terms for the exact requirement.
How much does a heat pump repair cost?
Heat pump repairs have a typical range of £90–£1,100, including VAT, depending on the part and labour involved. Sensor replacements sit at the lower end, while control boards and refrigerant repairs on split systems sit higher. Every repair starts with a fault-finding visit, with a guide price of £90–£180 for the first hour, and the repair is priced before work goes ahead.
Why is my heat pump showing an error code?
An error code is the heat pump's way of reporting a problem it has detected, such as low water flow, a sensor reading out of range or a communication fault between units. Note the code and check the manual, as some codes clear after a simple reset or pressure top-up. If it returns, an engineer can trace the underlying cause.